12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

|-----------------------------------------------------|¦ NOTE: For RAMP AND SOAK option, if the loop is run- ¦¦ ning a ramp and soak profile, forcing it into manual¦¦ removesthe loop from ramp and soak mode. The user ¦¦ must reassign and restart the profile to return to ¦¦ automatic ramp and soak operation. ¦|-----------------------------------------------------|4.7 SETUP RAMP/SOAK PROFILEPress YES at this prompt to setup or edit stored ramp and soak profile data including :- profile number- copy one profile to another- maximum out-of-tolerance time- ready state setpoint- ready event (digital output) states- segment number- segment time- segment setpoint- segment events- segment triggers- segment tolerance- last segment|-----------------------------------------------------|¦ NOTE: When leaving ramp and soak mode the loop is ¦¦ placed in MANUAL mode and the output is set to 0. ¦|-----------------------------------------------------|NOTE: This prompt will appear only if the 12LS has the rampinstalled.and soak option4.7.1 SELECT A PROFILE FOR EDITINGThis menu allows selection of one of twelve profiles [A-L] for editing. The default profile numberdisplayed in the prompt is either the last profile edited or PROFILE A if none has been edited.|-----------------|Display: ¦ EDIT RAMP & SOAK¦¦ PROFILE ? x ¦|-----------------|The ? flashes.x is the profile designator [A-L].YES Select a profile other than the default profile displayed.Lower display PROF = x4-45
UP/DOWNSelect a profile designator [A-L].4-46
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16:
3.0 INSTALLATIONThere are some prec
Page 17 and 18:
1/8th DIN HOUSING3-3
Page 19 and 20:
4. Use Thermocouple Extension Wire
Page 21 and 22:
3. Separate the 120 vac power leads
Page 23 and 24:
REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26:
3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28: WARNINGUse of the grounded T/C, mea
Page 29 and 30: 3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32: 3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34: ANAFAZE 12LS connections for a sing
Page 35 and 36: |- - - - - - - - - - - - - -|Back|-
Page 37 and 38: 4.2 DISPLAYSOn power-up the control
Page 39 and 40: |----------------------------------
Page 41 and 42: 4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44: 4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46: LOOP SETUP DATA|-------------------
Page 47 and 48: The menu appears as:|--------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77: PROFILE SETUP GUIDE4-44
Page 81 and 82: When any segment is out of toleranc
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100: 7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102: If ANASOFT runs then the next step
Page 103 and 104: Data Boundary ErrorThis Error Code
Page 105 and 106: The following examples show the out
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

Create successful ePaper yourself

Delete template?

Save as template?