12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

ENTERBACKNOBACKOpen the selected profile for editing. The display advances to theCopy Profile Menu.Return to SETUP R/S PROFILE ? prompt.Select the default profile for editing. The display advances to CopyAnother Profile.Return to the SETUP R/S PROFILE ? prompt.4.7.2 COPY ANOTHER PROFILEThis menu allows copying of another profile into the profile currently selected. This shortcutmethod is useful when the majority of a profile is similar to one that already exists.As a default choice the initial prompt offers to copy the profile immediately preceding the currentprofile (or L if editing profile A) but any of the other profiles may be selected.|---------------|Display: ¦ COPY SETUP ¦¦ FROM PROFILE ?¦|---------------|The ? flashes.x is the profile to be copied [A-L].YESSelect a profile to copy from.Lower display COPY = xUP/DOWNENTERBACKNOBACKSelect profile to copy.Copy profile contents. Display advancesto Edit Tolerance Alarm Time.Return to SETUP R/S PROFILE? prompt.Skip profile copying menu. Display advancesto Edit Tolerance Alarm Time.Return to SETUP R/S PROFILE? prompt.4.7.3 EDIT TOLERANCE ALARM TIMEWith this menu the maximum out-of-tolerance time for any segment within the profile may be set.Units are either Hours:Minutes or Minutes:Seconds depending on the global time base selected.Values from 00:01 to 99:59 may be entered. The default is 1:00.4-47
When any segment is out of tolerance for a period greater than the Tolerance Time entered, atolerance alarm is generated. A tolerance alarm activates the global annunciator output <strong>and</strong>displays a 'T' in the alarm status position on the display.|------------------|Display: ¦ x OUT-OF-TOLRNCE ¦¦ ALARM TIME:?hh:mm¦|------------------|x is the profile designator [A-L].The ? flashes.hh:mm is the current out-of-tolerance time limit.YESEdit the tolerance limit time.Lower display T =hh:mmUP/DOWNENTERBACKNOBACKAdjust time.Store the new setting. The display advances to Edit Ready Setpoint.Return to the SETUP R/S PROFILE? prompt.Leave tolerance time value as it is. The display advances to Edit ReadySetpoint.Return to the SETUP R/S PROFILE? prompt.4.7.4 EDIT READY SETPOINTThis menu allows editing of the ready state setpoint. This is the setpoint that will be loadedwhenever the profile is in the START (or ready) state.A profile enters START mode whenever it is first assigned to a loop. It also returns to STARTmode after completing execution.The ready setpoint provides a starting point at which segment 1 will begin.|----------------|Display: ¦ x READY SEGMENT¦¦ SETPOINT ? yyyy¦|----------------|The ? is flashing.x is the profile designator [A-L].yyyy is the current ready setpoint.YESUP/DOWNChange the ready state setpoint.Lower display SP =yyyyAdjust setpoint.4-48
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16:
3.0 INSTALLATIONThere are some prec
Page 17 and 18:
1/8th DIN HOUSING3-3
Page 19 and 20:
4. Use Thermocouple Extension Wire
Page 21 and 22:
3. Separate the 120 vac power leads
Page 23 and 24:
REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26:
3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28:
WARNINGUse of the grounded T/C, mea
Page 29 and 30: 3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32: 3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34: ANAFAZE 12LS connections for a sing
Page 35 and 36: |- - - - - - - - - - - - - -|Back|-
Page 37 and 38: 4.2 DISPLAYSOn power-up the control
Page 39 and 40: |----------------------------------
Page 41 and 42: 4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44: 4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46: LOOP SETUP DATA|-------------------
Page 47 and 48: The menu appears as:|--------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79: UP/DOWNSelect a profile designator
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100: 7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102: If ANASOFT runs then the next step
Page 103 and 104: Data Boundary ErrorThis Error Code
Page 105 and 106: The following examples show the out
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

Create successful ePaper yourself

Delete template?

Save as template?