12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

6.0 SOFTWAREANAFAZE offers turnkey software for IBM PC and compatible computers. The presentsoftware includes:ANASOFT-SVANASOFT-EVANASOFT-RSStandard Version for 12LS setupExpanded Version with graphics, data logging, and automatic job selection atstart up.ANASOFT-EV with ramp and soak, requires 12LS-RS6.1 ANASOFTANASOFT is a menu driven program that operates ANAFAZE 12LS controllers using an IBMPC or compatible computer. It provides a summary screen with color graphic displays of systemoperating conditions. ANASOFT-EV includes graphic plotting, data acquisition, alarmindication, and many other features. Please request the ANASOFT data sheet for moreinformation.6.2 CUSTOM APPLICATION PROGRAMSANAFAZE maintains a staff of engineers that can provide assistance in generating software forcustom applications. In addition ANAFAZE will design and implement your entire turn keyhardware and software system. Please contact your local representative or ANAFAZE directlyfor a quotation.6-1
7.0 TROUBLE SHOOTING INFORMATION7.1 Stand Alone SystemsFor stand alone systems the ANAFAZE 12LS should be returned to ANAFAZE when problemsoccur. If the unit has no display check the input power supply.Normally there are no components that can be field repaired. The 12LS can be checked atANAFAZE using a test fixture that checks the different boards.If a spare unit is inserted set the entered values to the ones of the replaced unit. These values canbe stored and entered using a standard IBM PC or compatible computer and ANASOFTsoftware.7.1.1 Checking Control OutputsControl outputs can be checked by setting the loop to manual and the control output to thedesired level. An LED with a series 1K resistor can be connected across the output to see if it ispulsing.7.1.2 Checking Digital I/OThe digital I/O can be checked from the Test I/O menu. Again the LED with series 1k resistorcan be used to see the outputs pulse on and off.7.2 Computer Supervised SystemsThese four items must work together to operate the 12LS:The 12LSThe computer including the RS-232 or other serial interfaceThe communications linkThe computer softwareIf the system does not work on initial start up check the 12LS, the computer, and the serial link.The 12LS first be checked in the stand alone mode. If there is a problem the 12LS should bereturned to ANAFAZE for service.If ANASOFT is running in the system, when a unit is replaced, ANASOFT will detect acontroller reset [indicated on initial power up] and automatically reload the current parameters inANASOFT.If the system includes multiple ANAFAZE 12LS controllers the address must be set to thecorrect address. This should be done using a spare housing before plugging the unit into thesystem housing.7-1
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16:
3.0 INSTALLATIONThere are some prec
Page 17 and 18:
1/8th DIN HOUSING3-3
Page 19 and 20:
4. Use Thermocouple Extension Wire
Page 21 and 22:
3. Separate the 120 vac power leads
Page 23 and 24:
REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26:
3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28:
WARNINGUse of the grounded T/C, mea
Page 29 and 30:
3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32:
3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34:
ANAFAZE 12LS connections for a sing
Page 35 and 36:
|- - - - - - - - - - - - - -|Back|-
Page 37 and 38:
4.2 DISPLAYSOn power-up the control
Page 39 and 40:
|----------------------------------
Page 41 and 42:
4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44:
4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46:
LOOP SETUP DATA|-------------------
Page 47 and 48: The menu appears as:|--------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79 and 80: UP/DOWNSelect a profile designator
Page 81 and 82: When any segment is out of toleranc
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 101 and 102: If ANASOFT runs then the next step
Page 103 and 104: Data Boundary ErrorThis Error Code
Page 105 and 106: The following examples show the out
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?