12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

4.5.6.1 DIGITAL INPUT TESTINGThis is a view-only display showing the logic state of the 8 digital inputs as 1's (High) or 0's (Low). The displayappears as:|----------------|¦ DIGITAL INPUTS ¦¦ xxxxxxxx ¦|----------------|Input 1 --| |-- Input 8Press any key to advance to the TEST OUTPUT SELECTION display.4.5.6.2 TEST OUTPUT SELECTIONThis menu allows the user to select one of the 9 digital outputs for manual operation. The display appears as :|----------------|¦ DIGITAL OUTPUTS¦¦ TEST OUTPUT? x¦|----------------|Press YES to select the menu or NO to go on to the OUTPUT TEST display.Press UP and DOWN to choose the output number for test.Press ENTER to select the displayed output for test or press BACK to return to the SINGLE LOOP display.4.5.6.3 DIGITAL OUTPUT TESTUse this display to manually toggle the state of a digital output between ON or OFF. The display will appear as :|----------------|¦ DIGITAL OUTPUT ¦¦ NUMBER yy? xxx¦|----------------|The lower line of the display shows the selected output number and the current output state, ON or OFF.Press YES or NO to toggle the output state between OFF and ON.Press the BACK key to return to the Test Output Selection menu.4-33
4.6 RAMP AND SOAK OPTIONThe ramp and soak option turns the 12LS into a powerful batch controller. Along with the powercomes a certain amount of complexity. In general, the features that are not as likely to be usedhave been set to default to a non-intrusive condition. For example, if there is not a requirement fordigital inputs as triggers, they will be ignored by the profile.Some planning is required to set up a successful profile and the Profile Setup Guide should becopied and used in configuring ramp and soak profiles. All the loop parameters should be enteredbefore starting on ramp and soak. If possible, test all loops for stability and control beforebeginning ramp and soak operation.In the ANAFAZE 12LS the RAMP AND SOAK OPTION allows up to 12 profiles to be specified,each containing a maximum of 20 segments. The 12 profiles are assigned letters A through L andare independent of the loops.Profiles are set up by their letter name and subsequently assigned to a loop. The same profile canbe assigned to any number of loops.|------------------------------------------------------|¦ NOTE : Care should be taken with digital inputs and ¦¦ outputs since these are specifically assigned to a ¦¦ profile. For example, if input 1 is used to start ¦¦ profile A, it will start that profile on all loops ¦¦ that use profile A. ¦|------------------------------------------------------|A channel is put into ramp and soak mode by assigning it a profile letter from A to L. Likewise, achannel is returned to normal manual/auto status by assigning it NONE.The profiles are edited from the password-protected RAMP & SOAK menu by profile letter.From this menu the user may create a profile from scratch or copy another profile for editing.Event outputs may be specified as NONE or 1-9, corresponding to the 9 available digital outputs.The ready segment contains an event state (ON or OFF) for each of these 9 output pins. Thedefault for each is OFF. All digital outputs function in an "OR" configuration and may be multiplydefined in various profiles. If any profile segment has turned the output on it will be on. Onlywhen all sources set the output off will it be turned off.Triggers may be specified as NONE or 1 through 8, corresponding to oneof 8 available digitalinputs.All times are entered in the same units: either hours and minutes or minutes and seconds. The timeformat is selected from the GLOBALS menu. All time variables are then understood to be in thesame units, although there is no explicit display of such. For either time base, segment times from000:01 to 999:59 may be entered. If using hours and minutes, this provides a range of 1 minute toover 41 days. Total profile time can stretch up to 2.28 years although profile time remaining canonly be displayed up to 999 hours and 59 minutes.4-34
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16: 3.0 INSTALLATIONThere are some prec
Page 17 and 18: 1/8th DIN HOUSING3-3
Page 19 and 20: 4. Use Thermocouple Extension Wire
Page 21 and 22: 3. Separate the 120 vac power leads
Page 23 and 24: REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26: 3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28: WARNINGUse of the grounded T/C, mea
Page 29 and 30: 3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32: 3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34: ANAFAZE 12LS connections for a sing
Page 35 and 36: |- - - - - - - - - - - - - -|Back|-
Page 37 and 38: 4.2 DISPLAYSOn power-up the control
Page 39 and 40: |----------------------------------
Page 41 and 42: 4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44: 4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46: LOOP SETUP DATA|-------------------
Page 47 and 48: The menu appears as:|--------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65: Press ENTER to store the status or
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79 and 80: UP/DOWNSelect a profile designator
Page 81 and 82: When any segment is out of toleranc
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100: 7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102: If ANASOFT runs then the next step
Page 103 and 104: Data Boundary ErrorThis Error Code
Page 105 and 106: The following examples show the out
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?