12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

ENTERBACKNOBACKStore new ready state setpoint. Display will advance to Edit Ready EventStates.Return to SETUP R/S PROFILE? prompt.Skip edit. Leave ready setpoint as it is. Display will advance to Edit ReadyEvent States.Return to the SETUP R/S PROFILE? prompt.4.7.5 EDIT READY EVENT STATESThis menu allows setting of default states for all possible 9 event outputs. These will be the outputstates whenever the loop is in the (S)TART state. The default for all outputs is OFF.Display:|----------------|¦ x READY SEGMENT¦¦ EDIT EVENTS ? ¦|----------------|The ? is flashing.x is the profile designator [A-L].YESEdit default output states.Lower display DOxx?yyyThe ? is flashing.xx is an event output number [1-9].yyy is output state, OFF or ON.YESEdit state of output selected.Lower display DOxx=yyyUP/DOWNENTERBACKNOBACKNOToggles state to ON or OFF.Sets selected output ready stateto ON or OFF. Display advancesto next output.Quit editing. Return to READYEVENTS? prompt.Select next output.Quit editing. Return to READYEVENTS? prompt.Skip ready event editing. Displayadvances to Edit SegmentNumber.4-49
4.7.6 EDIT EXTERNAL RESETFrom this menu one of the eight digital inputs will be selected to provide an input for a externalreset of this profile while in any of the R/S operational modes. A selection of 0 will disable thisfunction. The same input may be assigned to more than one profile.|-----------------|Display: ¦ x EXTERNAL RESET¦¦ INPUT NUMBER? d ¦|-----------------|YESThe ? is flashing.x is the profile designator [A-L].d is the assigned digital input number [1-8], 0 for noassignment-external reset disabled.Change digital input number assigned to this profile.Lower display INPUT NUMBER= dUP/DOWNENTERBACKSelect digital input number.Assign digital input number for the external reset function.Return to Setup Ramp/Soak Profile?4.7.7 EDIT SEGMENT NUMBERFrom this menu one of the twenty profile segments may be selected for editing. The defaultnumber will be either the last segment edited or SEGMENT 1 if none has been edited. Whenentering profile data sequentially the segment number will automatically increment to the nextsegment each time this menu is entered.Display:|---------------|¦ x EDIT SEGMENT¦¦ NUMBER ? yy ¦|---------------|The ? flashes.x is the profile designator [A-L].yy is the default segment number [1-20].YESSelect a segment other than the default segment for editing.Lower display SEG = xxUP/DOWNENTERBACKSelect segment number.Open selected segment for editing. Display advances to Edit Segment Time.Return to SETUP R/S PROFILE? prompt.4-50
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16:
3.0 INSTALLATIONThere are some prec
Page 17 and 18:
1/8th DIN HOUSING3-3
Page 19 and 20:
4. Use Thermocouple Extension Wire
Page 21 and 22:
3. Separate the 120 vac power leads
Page 23 and 24:
REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26:
3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28:
WARNINGUse of the grounded T/C, mea
Page 29 and 30:
3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32: 3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34: ANAFAZE 12LS connections for a sing
Page 35 and 36: |- - - - - - - - - - - - - -|Back|-
Page 37 and 38: 4.2 DISPLAYSOn power-up the control
Page 39 and 40: |----------------------------------
Page 41 and 42: 4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44: 4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46: LOOP SETUP DATA|-------------------
Page 47 and 48: The menu appears as:|--------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79 and 80: UP/DOWNSelect a profile designator
Page 81: When any segment is out of toleranc
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100: 7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102: If ANASOFT runs then the next step
Page 103 and 104: Data Boundary ErrorThis Error Code
Page 105 and 106: The following examples show the out
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?