12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

|-----------------------------------------------------|¦ NOTE: Unless otherwise specified, in all examples ¦¦of menu displays in the following discussions about ¦¦editing and programming, the question mark (?) would ¦¦ be blinking and the multiple x's used represent the ¦¦ data or choice to be edited. When a menu is selected¦¦ the x's would show the current data setting and the ¦¦ question mark (?) would become an equal sign (=) ¦|-----------------------------------------------------|4.5.1 SETUP GLOBAL PARAMETERS?Answer YES at this prompt to access editing menus for global system parameters. This group of menus includes thosethat allow the user to :o Save memory to a job numbero Restore a job number to memoryo Set the alarm delayo Select the global time baseo Lock out panel editingo Select output state on power-upo Set the controller communications addresso Set the communications error checking methodo Set the communications baud rateo Set the AC line frequencyo Check the PROM version and date4.5.1.1 STORING JOB SETUPThe current operating parameters may be stored in battery-backed memory by saving them to one of 8 job files.Information for all 12 channels is saved in each job file and includes :o Setpointso Output percentage- both heatand cool output valueso Channel status (auto, manual, etc.)o Alarminformation- status- setpoints- output assignmentso Assigned ramp and soak profile if in ramp/soak mode4-13
The menu appears as:|----------------|¦SAVE CURRENT ¦¦SETUP TO JOB ? x¦|----------------|When this menu is first displayed the job number will be the number of the last job file selected, or 1 by default.Press YES to select the menu or NO to advance to the next menu.Press UP and DOWN to select the job number.Press ENTER to store current setup to the selected job file or press BACK to return to the SETUP GLOBALPARAMETERS main menu heading.4.5.1.2 RESTORING A JOB SETUPAny one of 8 saved jobs may be loaded for operation from memory. The parameters loaded into memory when a jobis loaded are the same as those listed above under Storing Job Setup. All existing data will be overwritten. The displaywill appear as :|----------------|¦LOAD CURRENT ¦¦SETUP FM JOB ? x¦|----------------|When this menu is first displayed the job number will be the number of the last job selected, or 1 by default.Press YES to select the menu or NO to advance to the next menu.Press UP and DOWN to select the job number.Press ENTER to load the current setup from the selected job file or press BACK to return to the SETUP GLOBALPARAMETERS main menu heading.4.5.1.3 SETTING THE ALARM DELAYThis menu is used to set a startup delay for all system alarms. Alarm checking will be delayed for the number ofminutes entered [0 to 60]. This is used to avoid nuisance alarms when starting up a system. The display will appear as :|----------------|¦ ALARM DELAY ¦¦ ? xx MINUTE(S)¦|----------------|Press YES to select the menu or NO to advance to the next menu.Press UP and DOWN to adjust the number of minutes desired.4-14
Page 1 and 2: ANAFAZE 12LSInstallation And Operat
Page 3 and 4: WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6: 4.4 OPERATIONAL MENUS..............
Page 7 and 8: vii
Page 9 and 10: The ANAFAZE 12LS front panel provid
Page 11 and 12: Digital Inputs and Outputs Expand V
Page 13 and 14: 2.2 Control CapabilityNumber of Loo
Page 15 and 16: 3.0 INSTALLATIONThere are some prec
Page 17 and 18: 1/8th DIN HOUSING3-3
Page 19 and 20: 4. Use Thermocouple Extension Wire
Page 21 and 22: 3. Separate the 120 vac power leads
Page 23 and 24: REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26: 3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28: WARNINGUse of the grounded T/C, mea
Page 29 and 30: 3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32: 3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34: ANAFAZE 12LS connections for a sing
Page 35 and 36: |- - - - - - - - - - - - - -|Back|-
Page 37 and 38: 4.2 DISPLAYSOn power-up the control
Page 39 and 40: |----------------------------------
Page 41 and 42: 4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44: 4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45: LOOP SETUP DATA|-------------------
Page 49 and 50: 4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52: Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79 and 80: UP/DOWNSelect a profile designator
Page 81 and 82: When any segment is out of toleranc
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98:
5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100:
7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102:
If ANASOFT runs then the next step
Page 103 and 104:
Data Boundary ErrorThis Error Code
Page 105 and 106:
The following examples show the out
Page 107 and 108:
Cycle TimeDeviationAlarmThe time ba
Page 110:
Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

Create successful ePaper yourself

Delete template?

Save as template?