- Page 1 and 2:
SHR -A-379 The SUPERPAVE Mix Design
- Page 3 and 4:
Acknowledgments The research descri
- Page 5 and 6:
M-003 Determining the Shear and Sti
- Page 7 and 8:
Introduction This volume of the Fin
- Page 9 and 10:
Table 2. AASHTO and Other Test Meth
- Page 11 and 12:
T48 Method of Test for Flash and Fi
- Page 13 and 14:
10. KEY WORDS Asphalt binder, aspha
- Page 15 and 16:
Table 1. Performance-Graded Asphalt
- Page 17 and 18:
2.2 ASTM Standards: C802 Conducting
- Page 19 and 20:
7. APPARATUS 7.1 Bending Beam Rheom
- Page 21 and 22:
7.6 Calibrated Thermometers--Calibr
- Page 23 and 24:
11.3 Perform a daily quality contro
- Page 25 and 26:
NOTE9.--The specified preload on th
- Page 27 and 28:
dG d2 --_ I d __
- Page 29 and 30:
CO U_ P z_ MLLI L_O° _ _ _c_ r_ j4
- Page 31 and 32:
m) _L wO O_ W _Z _W W_ Z w W_ 0 _ w
- Page 33 and 34:
1.4 Maximum bending stress--The max
- Page 35 and 36:
Sy = log S(8) + log S(15) + ... log
- Page 37 and 38:
Z 1.3 1.2 1.1 , , .... J 1 • '; "
- Page 39 and 40:
T240 Test Method for Effect of Heat
- Page 41 and 42:
5.2 The complex shear modulus is an
- Page 43 and 44:
7. HAZARDS 7.1 Standard laboratory
- Page 45 and 46: 9.1.1.2.3 A thermocouple probe shal
- Page 47 and 48: Typically, reliable test results ma
- Page 49 and 50: figure 1 can be generated by gradua
- Page 51 and 52: 150 "ZERO" STRAIN VALUE O" STRAIN V
- Page 53 and 54: T179 Test Method for Effect of Heat
- Page 55 and 56: 5.3 For evaluating an asphalt binde
- Page 57 and 58: time. A change in the load signal e
- Page 59 and 60: 9.1.1 Load cell--Verify calibration
- Page 61 and 62: 11.2 Immediately after demolding, p
- Page 63 and 64: 13.1.5 the average failure strain,
- Page 65 and 66: IA A 5,0 I 6 0 86,0 9,5 FILLET O,K.
- Page 67 and 68: --__6_- -_A AL AL _ o 0 _ _ _ "_ f-
- Page 69 and 70: I __;___ i --_'-- :" (_ . /_/Spring
- Page 71 and 72: T179 Test Method for Effect of Heat
- Page 73 and 74: points within the pressure vessel a
- Page 75 and 76: NOTE7.--Aging temperature in the PA
- Page 77 and 78: 13. KEY WORDS Accelerated aging, el
- Page 79 and 80: to temperaturetransducerand te_llpe
- Page 81 and 82: 3. SUMMARY OF METHOD 3.1 The paving
- Page 83 and 84: 7. PRECAUTIONS 7.1 Solvents should
- Page 85 and 86: 9.4 Final Extraction and Recovery 9
- Page 87 and 88: Glass Wool Plug Figure 2. Extractio
- Page 89 and 90: 5.761 in I.D. 6 holes 3/16 in I.D.
- Page 91 and 92: 1/4 I.D. 5 3/4 in I.D. 6 holes 5/16
- Page 93 and 94: Polypropylene Cloth Filter I" .....
- Page 95: 114 in I.D. 11 1/4 in I.D. 8 holes
- Page 99 and 100: drying should be re-dried. Caution:
- Page 101 and 102: 8.16 Clean the funnels, volumetric
- Page 103 and 104: Adsorption/Desorption Testing Data
- Page 105 and 106: 2.3 ASTM Standards: D 4402 Measurem
- Page 107 and 108: 5.6.3 Start time of test; 5.6.4 Spe
- Page 109 and 110: 9.1.1 Weigh the aggregate fractions
- Page 111 and 112: 11. CALCULATIONS AND INTERPRETATION
- Page 113 and 114: 3.1 Test System--The test system is
- Page 115 and 116: 4.3 Determine Air Void Content--Det
- Page 117 and 118: • vertical displacement of the sp
- Page 119 and 120: The following engineering quantitie
- Page 121 and 122: the axial actuator is under closed
- Page 123 and 124: Figure 2. Platen-Specimen Assembly
- Page 125 and 126: Figure 4. Positioning of Vertical a
- Page 127 and 128: tO0 © © ....... OT...=.c on A TEM
- Page 129 and 130: Standard Method of Test for Determi
- Page 131 and 132: 3. SUMMARY OF METHOD 3.1 This test
- Page 133 and 134: 6.5.1 For analog strip-chart record
- Page 135 and 136: 8. PROCEDURE 8.1 Measure the bulk s
- Page 137 and 138: movement per minute. Both the horiz
- Page 139 and 140: If E is greater than 0.01, substitu
- Page 141 and 142: Table 1. Correction Factors for Hor
- Page 143 and 144: Figure 2. Specimen Loading Frame wi
- Page 145 and 146: Standard Method of Test for Determi
- Page 147 and 148:
6. APPARATUS 6.1 Environmental Cond
- Page 149 and 150:
9.3 Heat or cool the asphalt concre
- Page 151 and 152:
pressed. Otherwise, measure and rec
- Page 153 and 154:
10.7.2.3 Apply a repeated axial com
- Page 155 and 156:
11.3.1 Peak Stress (kPa) per load c
- Page 157 and 158:
12.1.3 Aggregate Type and Gradation
- Page 159 and 160:
Specimen Temperature Hi/Lo Limit Pr
- Page 161 and 162:
i Pressure Differential Gauge /_ 0
- Page 163 and 164:
I0 0 0 0 0 0 0 0 0 Ooo00 0 0 '_,Oo
- Page 165 and 166:
" Total Elastic 0 Ei._ 0 121 Plasti
- Page 167 and 168:
T201 Method of Test for Kinematic V
- Page 169 and 170:
6.4.4 One metal spatula or spoon 6.
- Page 171 and 172:
11.1.1 Asphalt Binder Grade 11.1.2
- Page 173 and 174:
D 1561-81a Preparation of Bituminou
- Page 175 and 176:
After filling, close all containers
- Page 177 and 178:
l i /l Gmb = . (1) B-Cwhere A = Mas
- Page 179 and 180:
8. REPORT 8.1 The report shall incl
- Page 181 and 182:
1 RAMP, ..:i!i!iiiii:i:i:i:i:i:i:i:
- Page 183 and 184:
Standard Method of Test for Determi
- Page 185 and 186:
3.3 Epoxy Nut to Neutral Axis of Sp
- Page 187 and 188:
5.1.6 Cumulative Dissipated Energy
- Page 189 and 190:
plot 6.1.11 Plot of Dissipated Ener
- Page 191 and 192:
Figure 2. Nut Epoxied to Neutral Ax
- Page 193 and 194:
Figure 4. Nut/Block/Screw/LVDT Conn
- Page 195 and 196:
0 OO £ m -r"_ mlO 5 10 4 , [ 'T I
- Page 197 and 198:
As a minimum, the test system, shou
- Page 199 and 200:
With the ink marker, trace diar_.et
- Page 201 and 202:
5. CALCULATIONS A_er the specime_ f
- Page 203 and 204:
Step Motor L,.._ Loading Rod Swivel
- Page 205 and 206:
ATHENA TEMPERATURECONTROLLER ii:!i:
- Page 207 and 208:
Standard Practice for The Laborator
- Page 209 and 210:
2.2 SHRP Documents B-006 Extraction
- Page 211 and 212:
using the same SUPERPAVE ® perform
- Page 213 and 214:
must be used with the modifier from
- Page 215 and 216:
8.2.3 Sections 8.3 and 8.4 present
- Page 217 and 218:
8.8.2 Conditioning and Testing--Car
- Page 219 and 220:
9. LABORATORY EVALUATION OF AGGREGA
- Page 221 and 222:
shear, volumetric and frequency swe
- Page 223 and 224:
12.2 The HMA plant should produce t
- Page 225 and 226:
Table 1. Modifier Selection and Cha
- Page 227 and 228:
Table 5. Guidelines for Binder Modi
- Page 229 and 230:
Standard Practice for Grading or Ve
- Page 231 and 232:
6. TEST PROCEDURE FOR GRADING AN UN
- Page 233 and 234:
7. TEST PROCEDURE FOR VERIFYING THE
- Page 235 and 236:
8. REPORT 8.1 If the grade of the a
- Page 237 and 238:
1.4 In order to attain adequate pre
- Page 239 and 240:
5.4 Calculate the bulk specific gra
- Page 241 and 242:
Standard Practice for Measurement o
- Page 243 and 244:
Table 1. Test Matrix for Level 2 Mi
- Page 245 and 246:
6. SPECIMEN PREPARATION 6.1 All tes
- Page 247 and 248:
Record axial deformation, shear def
- Page 249 and 250:
7.3.5 Since the specimen will be su
- Page 251 and 252:
NOTE 15.--At each temperature, the
- Page 253 and 254:
Table 7. Time Estimate for Level 2
- Page 255:
NOTEA1.2.--This stress-controlled t