Numonyxâ„¢ Wireless Flash Memory (W30)

More documents

Recommendations

Info

Numonyx Wireless Flash Memory (W30) (W30) 5.0 Maximum Ratings and Operating Conditions 5.1 Absolute Maximum Ratings Warning: Stressing the flash device beyond the Absolute Maximum Ratings in Table 7 might cause permanent damage. These are stress ratings only. Notice: This datasheet contains information on products in the design phase of development. The information here is subject to change without notice. Do not finalize a design with this information. Table 7: Absolute Maximum Ratings 5.2 Operating Conditions Parameter Maximum Rating Note Temperature under Bias –40 °C to +85 °C Storage Temperature –65 °C to +125 °C Voltage on Any Pin (except VCC , VCCQ , VPP ) –0.5 V to +3.8 V VPP Voltage –0.2 V to +14 V 1,2,3 V CC Voltage –0.2 V to +2.45 V 1 VCCQ Voltage –0.2 V to +3.8 V 1 Output Short Circuit Current Notes: 100 mA 4 1. 2. 3. All specified voltages are relative to VSS. Minimum DC voltage is –0.5 V on input/output pins and –0.2 V on VCC and VPP pins. During transitions, this level might undershoot to –2.0 V for periods < 20 ns. Maximum DC voltage on input/output pins is VCC +0.5 V which, during transitions, might overshoot to VCC +2.0 V for periods < 20 ns. Maximum DC voltage on VPP might overshoot to +14.0 V for periods < 20 ns. VPP program voltage is normally VPPL. VPP can be 12 V ± 0.6 V for 1000 cycles on the main blocks and 2500 cycles on the parameter blocks during program/erase. 4. Output shorted for no more than one second. No more than one output shorted at a time. Do not operate the W30 flash memory device beyond the Operating Conditions in Table 8. Extended exposure beyond these Operating Conditions might affect flash device reliability. Table 8: Extended Temperature Operation (Sheet 1 of 2) Symbol Parameter 1 Min Nom Max Unit Notes TA Operating Temperature –40 25 85 °C - VCC VCC Supply Voltage 1.7 1.8 1.90 VCCQ I/O Supply Voltage 2.2 3.0 3.3 3 V VPPL VPP Voltage Supply (Logic Level) 0.90 1.80 1.95 2 V PPH Factory Programming V PP 11.4 12.0 12.6 2 t PPH Maximum V PP Hours V PP = 12 V - - 80 Hours 2 Datasheet November 2007 24 Order Number: 290702-13 3
Numonyx Wireless Flash Memory (W30) Table 8: Extended Temperature Operation (Sheet 2 of 2) Symbol Parameter 1 Min Nom Max Unit Notes Block Erase Cycles Main and Parameter Blocks Main Blocks Parameter Blocks VPP < VCC VPP = 12 V VPP = 12 V 100,000 - - - - - - 1000 2500 Cycles 2 2 Notes: 1. See Section 6.1, “DC Current Characteristics” on page 26 and Section 6.2, “DC Voltage Characteristics” on page 27 for specific voltage-range specifications. 2. VPP is normally VPPL . VPP can be connected to 11.4 V–12.6 V for 1000 cycles on main blocks for extended temperatures and 2500 cycles on parameter blocks at extended temperature. 3. 4. Contact your Numonyx field representative for VCC /VCCQ operations down to 1.65 V. See the tables in Section 6.0, “Electrical Specifications” on page 26 and in Section 7.0, “AC Characteristics” on page 28 for operating characteristics November 2007 Datasheet Order Number: 290702-13 25 2
Page 2 and 3: Legal Lines and Disclaimers INFORMA
Page 4 and 5: Numonyx Wireless Flash Memory (W30)
Page 6 and 7: Date of Revision 11/17/03 -008 Vers
Page 8 and 9: • RWE - Read-While-Erase • RWW
Page 12 and 13: Table 2: Top Parameter Memory Map M
Page 14 and 15: Figure 2: 32Mb, 64Mb and 128Mb QUAD
Page 16 and 17: Figure 4: 32Mb VF BGA Package Drawi
Page 18 and 19: 4.0 Ballout and Signal Descriptions
Page 20 and 21: 4.2 Signal Descriptions Numonyx Wir
Page 22 and 23: Table 6: Signal Descriptions - QUAD
Page 26 and 27: 6.0 Electrical Specifications 6.1 D
Page 28 and 29: 7.0 AC Characteristics 7.1 Read Ope
Page 30 and 31: Table 12: Read Operations - 180 nm
Page 32 and 33: Figure 9: Latched Asynchronous Read
Page 34 and 35: Figure 11: Single Synchronous Read-
Page 38 and 39: Figure 15: Burst Suspend CLK Addres
Page 40 and 41: Figure 16: Write Operations Wavefor
Page 42 and 43: Figure 19: Synchronous Read to Writ
Page 44 and 45: 8.0 Power and Reset Specifications
Page 46 and 47: 8.6 Reset Specifications Table 15:
Page 48 and 49: 9.0 Flash Device Operations Numonyx
Page 50 and 51: 9.1.4 Reset 9.1.5 Write Numonyx Wir
Page 52 and 53: Table 18: Command Codes and Descrip
Page 54 and 55: Figure 26: Interleaving a 2-Cycle W
Page 56 and 57: Table 20: Flash Device Identificati
Page 58 and 59: 10.5 Clear Status Register Numonyx
Page 60 and 61: Figure 28: Word Program Flowchart S
Page 62 and 63: 11.3.2 Setup Numonyx Wireless Flash
Page 64 and 65: Figure 29: Enhanced Factory Program
Page 72 and 73: Figure 33: Block Locking State Diag
Page 74 and 75:
Numonyx Wireless Flash Memory (W30)
Page 76 and 77:
Table 26: Simultaneous Operations A
Page 78 and 79:
Figure 36: Protection Register Lock
Page 80 and 81:
Table 28: Read Configuration Regist
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Appendix A Write State Machine Numo
Page 88 and 89:
Page 90 and 91:
B.2 Query Structure Overview Numony
Page 92 and 93:
Table 37: System Interface Informat
Page 94 and 95:
B.6 Numonyx-Specific Extended Query
Page 96 and 97:
Table 43: Partition Region 1 Inform
Page 98 and 99:
Table 45: Partition and Erase-Block
Page 100 and 101:
Table 47: 48F Type Stacked Componen
Page 102:
Table 51: Parameter / Mux Configura
show all

Numonyxâ„¢ Wireless Flash Memory (W30)

Create successful ePaper yourself

Delete template?

Save as template?