Accutorr Plus Service Manual - Mindray

More documents

Recommendations

Info

This page intentionally left blank. 5-44 Accutorr Plus Service Manual Chapter 5 - Schematics
6.0 REPLACEMENT PARTS CONTENTS OF THIS CHAPTER ..........................Page 6.1 Introduction.........................................6-1 6.2 Available Replacement Parts and Sub-Assemblies. ...........6-1 6.3 Product Variations and Options ..........................6-1 6.4 Exchange Program ...................................6-1 6.5 Replacement Parts Pricing Information ....................6-2 6.6 Ordering Information. .................................6-2 6.7 Abbreviations .......................................6-3 6.8 Isometric Drawings and Parts Lists. .......................6-5 6.9 Circuit Board Parts Lists................................6-19 6.1 INTRODUCTION This chapter of the Service Manual provides information necessary to identify the replacement parts and assemblies of the instrument. 6.2 AVAILABLE REPLACEMENT PARTS AND SUB-ASSEMBLIES The parts listings which follow are divided into two sections. The Isometric Drawings and the accompanying parts lists identify the available chassis mounted components. A listing for the components on each circuit board then follows. 6.3 PRODUCT VARIATIONS AND OPTIONS Product variations, due to differences for various line voltages, options and languages may require different components. These variations are reflected, where necessary, on the parts lists. 6.4 EXCHANGE PROGRAM Datascope offers an exchange policy for most of the printed circuit board assemblies. This program may provide the most expedient method of servicing the equipment. A standard charge for this service is made. Contact the Datascope Service Department for details concerning this exchange program. Many circuit boards make extensive use of multi-layer technology and high density packaging. Individual component replacement is not recommended on these boards unless the technician is properly equipped to repair multi-layer circuit boards. Accutorr Plus Service Manual 6-1 Chapter 6 - Parts
Page 1 and 2:
INTRODUCTION Chapters 1. Operation
Page 3 and 4:
TABLE OF CONTENTS INTRODUCTION ....
Page 5 and 6:
2.2.11 Masimo SET Technology. ....
Page 7 and 8:
7.5.13 Verification of Accutorr Plu
Page 9 and 10:
1.0 OPERATION CONTENTS OF THIS CHAP
Page 11 and 12:
1.2 CONTROLS AND INDICATORS This se
Page 13:
1 2 3 4 5 6 7 8 SYS. DIA. NIBP Sp0
Page 17 and 18:
11. Select Key (Accutorr Plus model
Page 19 and 20:
29. Set Alarms Key This key is used
Page 21 and 22:
1.2.2 Rear Panel Figure 1-5 Rear Pa
Page 23 and 24:
1.2.4 Recorder Module Figure 1-7 Re
Page 25 and 26:
1.3. OPERATION This section of the
Page 27 and 28:
1.3.2.3 Room Number and Bed Letter
Page 29 and 30:
2. Attach the cuff hose to the NIBP
Page 31 and 32:
1.3.4 AUTOMATIC NIBP MEASUREMENTS (
Page 33 and 34:
1.3.5 ALARMS The Accutorr Plus prov
Page 35 and 36:
1.3.5.3 How to Mute Alarms When an
Page 37 and 38:
1.3.6.2 To View the Stored Measurem
Page 39 and 40:
1.3.8 SETTING THE LCD CONTRAST (Vie
Page 41 and 42:
1.3.10 SpO2 MEASUREMENTS (Accutorr
Page 43 and 44:
C. Sensor Connection to the Accutor
Page 45 and 46:
1.3.10.2 Sequence for establishing
Page 47 and 48:
If patient movement presents a prob
Page 49 and 50:
interference; and placement of a se
Page 54 and 55:
1.3.12 RECORDER (optional) The Accu
Page 56 and 57:
1.3.14 BATTERY OPERATION When the A
Page 58 and 59:
User Configuration Number Function
Page 60 and 61:
1.3.17 HOW TO ATTACH OPTIONAL THERM
Page 62 and 63:
1.3.19 PLACEMENT OF RECORDER PAPER
Page 64 and 65:
2.2 DETAILED CIRCUIT DESCRIPTIONS T
Page 66 and 67:
Notes: 1. Detailed functional descr
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
3. Perform NIBP functions. start m
Page 74 and 75:
FUNCTIONAL GROUP SIGNALS SIGNAL DES
Page 76 and 77:
Real Time Clock and NV RAM (RTC), U
Page 78 and 79:
Keypad interface The keypad is made
Page 80 and 81:
Software Control There are no softw
Page 82 and 83:
Figure 2-5 Recorder Module Control
Page 84 and 85:
2.2.5 SpO2 Module: (Accutorr Plus M
Page 86 and 87:
Figure 2-7 SpO2 Block Diagram Digit
Page 88 and 89:
2.2.7 Communication Board The Accut
Page 90 and 91:
Figure 2-9 LCD Inverter Module Bloc
Page 92 and 93:
Figur2-11 Datascope Interface Circu
Page 94 and 95:
Figure 2-12 2.2.12 Masimo Interface
Page 96 and 97:
Figure 2-13 Tone-Processor Module F
Page 98 and 99:
NIBP Measurement Cycle Time Less th
Page 100 and 101:
Masimo ® SpO2 Range: 40-100% SpO2
Page 102 and 103: 3.2 Safety Characteristics Risk (Le
Page 105 and 106: 4.0 REPAIR INFORMATION CONTENTS OF
Page 107 and 108: 2. Use the proper equipment. Specia
Page 109 and 110: 4.5.1 Isolating the Problem, System
Page 111 and 112: has been received by the Accutorr P
Page 113 and 114: 4.6 DISASSEMBLY INSTRUCTIONS PRECAU
Page 115 and 116: 4.6.7 Removal of the Motor Filter (
Page 117 and 118: 4.6.14 Thermometer, Predictive (opt
Page 119: 5.0 ASSEMBLY AND SCHEMATIC DIAGRAMS
Page 151: Schematic Drawing Main Power Supply
Page 165 and 166: 6.7 ABBREVIATIONS The following abb
Page 167 and 168: 6.8 ISOMETRIC DRAWINGS AND PARTS LI
Page 169 and 170: Figure Datascope No. Description Pa
Page 171 and 172: With NELLCOR SpO2 only Monitor Conf
Page 173: This page intentionally left blank.
Page 177 and 178: 6.8.3 Predictive Temperature Module
Page 179 and 180: 6.8.4 Mobile Stand Type 1 (Gray Bas
Page 181 and 182: 6.8.5 Mo bile Stand Type 2 (Black B
Page 184 and 185: Predictive Thermometer Bd Assy 0670
Page 186 and 187: Recorder Board Assembly 0670-00-058
Page 188 and 189: NIBP Circuit Board Assembly 0670-00
Page 190 and 191: SpO2 Board Assembly 0670-00-0593-03
Page 192 and 193: LCD Backlite Power Supply Board 067
Page 195 and 196: CPU/LED Board 0670-00-0650-03/04 It
Page 197 and 198: Communication Board 0670-00-0661-01
Page 199 and 200: Power Supply, Sealed Lead Acid 0014
Page 201 and 202: Power Sup ply, Lith ium Ion 0014-00
Page 203 and 204:
Power Sup ply, Lith ium Ion 0014-00
Page 205 and 206:
Masimo SpO2 Assy 0670-00-0716 Item
Page 207 and 208:
Tone Processor Module 0670-00-1134
Page 209 and 210:
7.0 CALIBRATION CONTENTS OF THIS CH
Page 211 and 212:
7.1 INTRODUCTION The Accutorr Plus
Page 213 and 214:
7.5.2 Software Version Test (0a, 0b
Page 215 and 216:
7.5.4 LED Test (2a, 2b) This test a
Page 217 and 218:
A fixed volume of 700 cc is pumped
Page 219 and 220:
7.5.12 Main Pressure Transducer Ver
Page 221 and 222:
4. Pump up the Cufflink simulator t
Page 223 and 224:
7.6.2 Water Bath Method 1. Prepare
Page 225 and 226:
Ambient temperature (TA) measured:
Page 227 and 228:
7.7.2 Set the Current Time 1. Press
Page 229 and 230:
7.9 TREND MEMORY INITIALIZATION 1.
Page 231 and 232:
SYS. DIA. NIBP SYS. DIA. NIBP 20/05
Page 233 and 234:
8.0 PREVENTIVE MAINTENANCE CONTENTS
Page 235 and 236:
This page intentionally left blank.
show all

Accutorr Plus Service Manual - Mindray

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?