Accutorr Plus Service Manual - Mindray

More documents

Recommendations

Info

21. Delete Info. Key Press the Data Scan key to enable the Delete Info. key (Accutorr Plus without Trend and SpO2 only). Once enabled, press and hold this key (1 beep tone, approx. 3 seconds) to delete the most recent reading when it is displayed. When displaying any measurement, press and hold this key (2 beep tones, approx. 6 seconds) to delete all information for the currently selected patient. Press and hold at power up to delete all information for all patients. 22. Data Scan Key Press this key (1 beep tone) to view previous measurements for the selected patient on the Accutorr Plus NIBP and to enable the Delete Info. key (Accutorr Plus without Trend and SpO2 only). The LED indicator next to the key illuminates. On the Accutorr Plus NIBP, use the Patient Info. Up & Down Arrow keys (27 & 28) to scroll through the stored measurements for the selected patient. On all models of the Accutorr Plus, press and hold this key (2 beep tones, approx. 6 seconds) to scan all of the rooms and beds for stored measurements. Press the Data Scan key again to stop on a particular room/bed. Press the Data Scan key again to exit this view mode. 23. Data Scan Indicator This LED indicator is illuminated when viewing prior data. 24. Room/Bed Number Key Press this key to change the displayed Room/Bed. After pressing this key use the Patient Info. Up & Down Arrow keys (27 & 28) to change the Room/Bed. This key is also used when selecting a User Configuration item. 25. Bed Letter Display This display is used to show the current patient bed letter. It is also used to display status codes for NIBP, SpO2 and Temperature and to display User Configuration items. 26. Room Number Display This display is used to show the current patient room number. It is also used to display status codes for NIBP, SpO2 and Temperature, indicates which alarm is being set (Hi or Lo), and displays a User Configuration item. 27. Patient Info. Down Arrow Key This key is used to decrement the alarm limits when they are shown on the LED displays and to decrement the hours, minutes, month, day and year in the clock set mode. This key is also used to change the Room/Bed, to scroll through previous data and to change initial inflation pressure. 28. Patient Info. Up Arrow Key This key is used to increment the alarm limits when they are shown on the LED displays and to increment the hours, minutes, month, day and year in the clock set mode. This key is also used to change the Room/Bed, to scroll through previous data and to change initial inflation pressure. 1-10 Accutorr Plus Service Manual Chapter 1, Operation
29. Set Alarms Key This key is used to select the NIBP and SpO2 (Accutorr Plus model with SpO2) alarms to be changed. Repeated presses of this key sequences through the choices of Systolic Hi, Systolic Lo, Diastolic Hi, Diastolic Lo, Map Hi, Map Lo, Pulse Rate Hi, Pulse Rate Lo, SpO2 Hi and SpO2 Lo. After the last available parameter, the next press returns the unit to normal operation. Once the desired parameter is flashing, use the Patient Info. Up & Down Arrow keys (27 & 28) to increment or decrement the alarm values. 30. Mute Key Press this key (one beep tone), to silence the current alarm tone for 2 minutes. If a new alarm is detected during the 2 minutes, a new alarm tone will sound. Press and hold (2 beep tones, approx. 3 seconds) to permanently silence all alarm tones. Press this key again (1 beep tone), to activate alarm tones. 31. Mute Indicator This LED indicator is illuminated when the alarm tone has been silenced permanently and when the alarm volume is set to OFF. 32. Timer/Temp Key This key is used to switch between viewing the elapsed time or the temperature in the Interval/Elap. Time/Temp Display. When viewing stored measurements on the Accutorr Plus NIBP, press this key to switch between viewing the temperature and time of the measurement. 33. Interval/Elap. Time/Temp Display This displays the time, in minutes since the last successful NIBP measurement (Elap. Time is illuminated). When the Interval key is pressed, the Elap. Time changes to the current Interval setting (Interval is illuminated). When the Predictive thermometer probe is removed from its holder, the Elap. Time changes to Temp (Temp is illuminated). Either “85.0" ( F) or ”29.4" ( C) will display; this is an internal self test feature. As the Predictive thermometer is taking a measurement, the display will flash as the number increases. When the final temperature measurement is determined, the display will no longer flash and a beep tone is generated. When the AccuTemp IR thermometer is used, the temperature is not displayed until after the measurement is taken and the thermometer is placed back into its holder. This display will also show the current time and date when setting the clock. 34. Interval Key Press to enter the set time interval mode. An interval is set for automatic NIBP measurement cycles. To sequence through the interval choices of: OFF (——, when set to display graphics), CONT (Continuous), 1, 2.5, 5, 10, 15, 20, 30, 60, 120 and 240 minutes, repeatedly press the Interval key. When the desired interval is displayed in the Interval/Elap. Time/Temp Display the TIMER/TEMP key may be pressed to enter the interval setting or, the displayed setting will be entered when 15 seconds have elapsed without pressing the Patient Info. Up or Down arrow keys (27 & 28). 35. Interval Indicator When an interval setting is selected, except for Off, the Interval Indicator flashes. When the interval mode is activated the Interval Indicator illuminates continuously. Accutorr Plus Service Manual Revised 06/25/99 1-11 Chapter 1, Operation
Page 1 and 2: INTRODUCTION Chapters 1. Operation
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION ....
Page 5 and 6: 2.2.11 Masimo SET Technology. ....
Page 7 and 8: 7.5.13 Verification of Accutorr Plu
Page 9 and 10: 1.0 OPERATION CONTENTS OF THIS CHAP
Page 11 and 12: 1.2 CONTROLS AND INDICATORS This se
Page 13: 1 2 3 4 5 6 7 8 SYS. DIA. NIBP Sp0
Page 17: 11. Select Key (Accutorr Plus model
Page 21 and 22: 1.2.2 Rear Panel Figure 1-5 Rear Pa
Page 23 and 24: 1.2.4 Recorder Module Figure 1-7 Re
Page 25 and 26: 1.3. OPERATION This section of the
Page 27 and 28: 1.3.2.3 Room Number and Bed Letter
Page 29 and 30: 2. Attach the cuff hose to the NIBP
Page 31 and 32: 1.3.4 AUTOMATIC NIBP MEASUREMENTS (
Page 33 and 34: 1.3.5 ALARMS The Accutorr Plus prov
Page 35 and 36: 1.3.5.3 How to Mute Alarms When an
Page 37 and 38: 1.3.6.2 To View the Stored Measurem
Page 39 and 40: 1.3.8 SETTING THE LCD CONTRAST (Vie
Page 41 and 42: 1.3.10 SpO2 MEASUREMENTS (Accutorr
Page 43 and 44: C. Sensor Connection to the Accutor
Page 45 and 46: 1.3.10.2 Sequence for establishing
Page 47 and 48: If patient movement presents a prob
Page 49 and 50: interference; and placement of a se
Page 54 and 55: 1.3.12 RECORDER (optional) The Accu
Page 56 and 57: 1.3.14 BATTERY OPERATION When the A
Page 58 and 59: User Configuration Number Function
Page 60 and 61: 1.3.17 HOW TO ATTACH OPTIONAL THERM
Page 62 and 63: 1.3.19 PLACEMENT OF RECORDER PAPER
Page 64 and 65: 2.2 DETAILED CIRCUIT DESCRIPTIONS T
Page 66 and 67: Notes: 1. Detailed functional descr
Page 68 and 69:
Notes: 1. Detailed functional descr
Page 70 and 71:
Notes: 1. Detailed functional descr
Page 72 and 73:
3. Perform NIBP functions. start m
Page 74 and 75:
FUNCTIONAL GROUP SIGNALS SIGNAL DES
Page 76 and 77:
Real Time Clock and NV RAM (RTC), U
Page 78 and 79:
Keypad interface The keypad is made
Page 80 and 81:
Software Control There are no softw
Page 82 and 83:
Figure 2-5 Recorder Module Control
Page 84 and 85:
2.2.5 SpO2 Module: (Accutorr Plus M
Page 86 and 87:
Figure 2-7 SpO2 Block Diagram Digit
Page 88 and 89:
2.2.7 Communication Board The Accut
Page 90 and 91:
Figure 2-9 LCD Inverter Module Bloc
Page 92 and 93:
Figur2-11 Datascope Interface Circu
Page 94 and 95:
Figure 2-12 2.2.12 Masimo Interface
Page 96 and 97:
Figure 2-13 Tone-Processor Module F
Page 98 and 99:
NIBP Measurement Cycle Time Less th
Page 100 and 101:
Masimo ® SpO2 Range: 40-100% SpO2
Page 102 and 103:
3.2 Safety Characteristics Risk (Le
Page 105 and 106:
4.0 REPAIR INFORMATION CONTENTS OF
Page 107 and 108:
2. Use the proper equipment. Specia
Page 109 and 110:
4.5.1 Isolating the Problem, System
Page 111 and 112:
has been received by the Accutorr P
Page 113 and 114:
4.6 DISASSEMBLY INSTRUCTIONS PRECAU
Page 115 and 116:
4.6.7 Removal of the Motor Filter (
Page 117 and 118:
4.6.14 Thermometer, Predictive (opt
Page 119:
5.0 ASSEMBLY AND SCHEMATIC DIAGRAMS
Page 151:
Schematic Drawing Main Power Supply
Page 163 and 164:
6.0 REPLACEMENT PARTS CONTENTS OF T
Page 165 and 166:
6.7 ABBREVIATIONS The following abb
Page 167 and 168:
6.8 ISOMETRIC DRAWINGS AND PARTS LI
Page 169 and 170:
Figure Datascope No. Description Pa
Page 171 and 172:
With NELLCOR SpO2 only Monitor Conf
Page 173:
This page intentionally left blank.
Page 177 and 178:
6.8.3 Predictive Temperature Module
Page 179 and 180:
6.8.4 Mobile Stand Type 1 (Gray Bas
Page 181 and 182:
6.8.5 Mo bile Stand Type 2 (Black B
Page 184 and 185:
Predictive Thermometer Bd Assy 0670
Page 186 and 187:
Recorder Board Assembly 0670-00-058
Page 188 and 189:
NIBP Circuit Board Assembly 0670-00
Page 190 and 191:
SpO2 Board Assembly 0670-00-0593-03
Page 192 and 193:
LCD Backlite Power Supply Board 067
Page 195 and 196:
CPU/LED Board 0670-00-0650-03/04 It
Page 197 and 198:
Communication Board 0670-00-0661-01
Page 199 and 200:
Power Supply, Sealed Lead Acid 0014
Page 201 and 202:
Power Sup ply, Lith ium Ion 0014-00
Page 203 and 204:
Power Sup ply, Lith ium Ion 0014-00
Page 205 and 206:
Masimo SpO2 Assy 0670-00-0716 Item
Page 207 and 208:
Tone Processor Module 0670-00-1134
Page 209 and 210:
7.0 CALIBRATION CONTENTS OF THIS CH
Page 211 and 212:
7.1 INTRODUCTION The Accutorr Plus
Page 213 and 214:
7.5.2 Software Version Test (0a, 0b
Page 215 and 216:
7.5.4 LED Test (2a, 2b) This test a
Page 217 and 218:
A fixed volume of 700 cc is pumped
Page 219 and 220:
7.5.12 Main Pressure Transducer Ver
Page 221 and 222:
4. Pump up the Cufflink simulator t
Page 223 and 224:
7.6.2 Water Bath Method 1. Prepare
Page 225 and 226:
Ambient temperature (TA) measured:
Page 227 and 228:
7.7.2 Set the Current Time 1. Press
Page 229 and 230:
7.9 TREND MEMORY INITIALIZATION 1.
Page 231 and 232:
SYS. DIA. NIBP SYS. DIA. NIBP 20/05
Page 233 and 234:
8.0 PREVENTIVE MAINTENANCE CONTENTS
Page 235 and 236:
This page intentionally left blank.
show all

Accutorr Plus Service Manual - Mindray

Create successful ePaper yourself

Delete template?

Save as template?