e-brick installation and user manual - GEW UV System v1.0

Recommendations

Info

3.1.3. Permanent Mounting For permanent mounting, brackets must be attached to the housing using the T-slots on the base of the unit. Ensure that the mounting surface (e.g. cabinet door, print station side panel) is sufficiently strong to support the weight of the e-Brick and attached cabling; four fixing points are recommended, see Figure 4. Figure 4: Cabinet mounting Note: the fixing brackets shown in Figure 4 are for illustration purposes only; specific brackets or fixings will be determined by the application. If necessary, please contact GEW for advice and engineering support. GEW UV e-Brick installation and operating manual 14 of 49
3.2. Space needed for use and maintenance The e-Brick requires little maintenance following installation but clearance is required to allow adequate cooling of the internal electronics. Allow the following clearances (see Figure 5): >500mm from the air intake >300mm from the exhaust outlet >25mm from sides If the e-Brick will be mounted in an enclosure rather than in free air, it is essential that adequate ventilation is provided. Refer to Table 2 for the rated power dissipation for each product variant; this figure should be taken in to account when calculating overall system cooling requirements. e-Brick variant Power dissipation (W) 3.6kW 300 9kW 475 12kW 900 22kW 1500 Table 2: Power dissipation Figure 5: Installation clearances GEW UV e-Brick installation and operating manual 15 of 49
Page 1 and 2: GEW UV DRYING SYSTEM e-Brick (EC) I
Page 3 and 4: 4.7. Conformity ...................
Page 5 and 6: Document Issue Status Issue Date EC
Page 7 and 8: 1. Product Description The UV dryin
Page 9 and 10: 1.1.5. Symbols used The following m
Page 11 and 12: 2.3. Handling Warning! e-Brick unit
Page 13: 3.1.2. Fitment of optional feet To
Page 17 and 18: 3.4. Connection to power supply War
Page 19 and 20: 4. Product information 4.1. Descrip
Page 21 and 22: 4.5. General Data 4.5.1. Electrical
Page 23 and 24: 4.6.2. Interface details Refer to s
Page 25 and 26: 4.6.3.1. P1: Press interface Pin co
Page 27 and 28: 4.6.3.5. P5: Power input Pin connec
Page 29 and 30: 4.7. Conformity Equipment Electroni
Page 31 and 32: 5.3. Setting and adjustment The e-B
Page 33 and 34: 5.6. Risk Reduction The GEW enginee
Page 35 and 36: 6. Maintenance information Warning!
Page 37 and 38: 6.5.1. General faults Water cooling
Page 39 and 40: Shutter failure Shutter failure whi
Page 41 and 42: 6.6. Parts list 6.6.1. Recommended
Page 43 and 44: 8. Emergency information 8.1. Fire
Page 45 and 46: 9.1.3. Exhaust filter change Warnin
Page 47 and 48: 10.1. Filter service record System
Page 49 and 50: 11.5. Making a Claim In the event o
Page 51 and 52: Table of Contents 1. Scope.........
Page 53 and 54: 1. Scope This document describes th
Page 55 and 56: Min power (Standby-100%) This sets
Page 57 and 58: Start the lamps Start running Monit
Page 59 and 60: Lamp power controls Whether power l
Page 61 and 62: 3.4.7. Consumable parts 3.4.8. GEW
Page 63 and 64: 3.5.1. Warning indicators The e-Bri
Page 65 and 66:
Safety switch failure On systems wi
Page 67 and 68:
3.6. HMI Flow chart General operati
Page 69 and 70:
REMOVE CHASSIS VCP, eCP, hCP NUVApl
Page 71:
REMOVE OLD LAMP Holding the lamp by
show all

e-brick installation and user manual - GEW UV System v1.0

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?