Repair Manual Mobile Generator - Wacker Neuson

More documents

Recommendations

Info

ECM Background Information Mobile Generator Repair 4.5 Additional Variables Monitored by the ECM Holding the toggle switch in the HOURS/RESET position allows the operator to view additional variables monitored by the ECM. It also allows the time-to-service countdown timer to be reset. To reset the countdown timer, hold the toggle switch in the HOURS/RESET position for approximately 30 seconds or until all the screens have scrolled through twice. Note: The values from your generator may differ slightly from those shown here. ECM Display Description SPN.FMI 100.01 Engine Hours 1.9 Time to Service 250 Throttle 10% Load @RPM 15% wc_tx001066gb.fm 30 John Deere engine diagnostic codes. SPN = Suspect Parameter Number. FMI = Failure Mode Identifier. The ten most recent codes will be displayed from most current to least current. See the John Deere Engine Manual for details. The display shows total time, in 1/10 hour increments, that the engine has been run. New machines, or machines with new ECMs, will read “No Data” because the engine has not been run for more than 1/10 of an hour. The display shows the amount of time left until service on the machine is required. To reset the timer to 250 hours, hold the Hours/Reset toggle switch in the up position until all the screens have scrolled through twice. The display shows the amount the throttle is open at the current point in time. The display shows the present load on the engine. For no load conditions (generator not powering any outside tools or equipment) the display will read 15%.
Mobile Generator Repair ECM Background Information Engine Torque 60% Fuel Temperature 86° F Fuel Pressure 147 Fuel Rate 0.9 GPH Manifold Temp 95°F wc_tx001066gb.fm 31 The display shows the percentage of total engine torque being used. The display shows, in °F, the temperature of the fuel. The display shows, in psi, the fuel pressure. The display shows, in gallons per hour (GPH), the rate at which fuel is being consumed. The display shows, in °F, the temperature of the engine intake manifold.
Page 1 and 2: 0175252en 004 0709 0 1 7 5 2 5 2 E
Page 3 and 4: Mobile Generator Repair Foreword Th
Page 5 and 6: G 70 Table of Contents 1 Safety Inf
Page 7 and 8: G 70 Table of Contents 8.13 Checkin
Page 9 and 10: G 70 Safety Information 1 Safety In
Page 11 and 12: G 70 Safety Information 1.1.17 ALWA
Page 13 and 14: G 70 Safety Information 1.2.11 ALWA
Page 15 and 16: G 70 Safety Information 1.4 Towing
Page 17 and 18: Mobile Generator Theory of Operatio
Page 23 and 24: Mobile Generator Electrical Testing
Page 25 and 26: Mobile Generator Repair ECM Backgro
Page 29: Mobile Generator Repair ECM Backgro
Page 39 and 40: G 70 ECM/Sensor Troubleshooting 5.1
Page 43 and 44: G 70 ECM/Sensor Troubleshooting Con
Page 45 and 46: G 70 ECM/Sensor Troubleshooting Con
Page 53 and 54: Mobile Generator Repair John Deere
Page 55 and 56: G 70 Troubleshooting Engine Start S
Page 67 and 68: G 70 Output Voltage Troubleshooting
Page 81 and 82:
G 70 Output Voltage Troubleshooting
Page 83 and 84:
G 70 Disassembly and Assembly 9 Dis
Page 85 and 86:
G 70 Disassembly and Assembly Conti
Page 87 and 88:
G 70 Disassembly and Assembly 9.6 I
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
G 70 Disassembly and Assembly 9.9 R
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
G 70 Schematics 10.2 Engine Wiring
Page 101 and 102:
G 70 Schematics 10.4 Generator Wiri
Page 103 and 104:
G 70 Technical Data 11.2 Generator
Page 105 and 106:
G 70 Technical Data 11.4 Dimensions
Page 107 and 108:
Threadlockers and Sealants Threadlo
Page 109 and 110:
Torque Values Torque Values (contin
show all

Repair Manual Mobile Generator - Wacker Neuson

Create successful ePaper yourself

Delete template?

Save as template?