CNC 8037 T - Operating manual - Fagor Automation

More documents

Recommendations

Info

CNC 8037 ·16· Safety conditions Symbols which may appear on the manual. i PRECAUTIONS DURING REPAIR Do not open this unit. Only personnel authorized by Fagor Automation may open this unit. Do not handle the connectors with the unit connected to mains. Before manipulating the connectors (inputs/outputs, feedback, etc.) make sure that the unit is not connected to AC power. SAFETY SYMBOLS Symbol for danger or prohibition. It indicates actions or operations that may cause damage to people or to units. Warning symbol. It indicates situations that may be caused by certain operations and the actions to be taken to prevent them. Obligation symbol. It indicates actions and operations that must be carried out. Information symbol. It indicates notes, warnings and advises.
WARRANTY TERMS INITIAL WARRANTY All products manufactured or marketed by FAGOR carry a 12-month warranty for the end user which could be controlled by the our service network by means of the warranty control system established by FAGOR for this purpose. In order to prevent the possibility of having the time period from the time a product leaves our warehouse until the end user actually receives it run against this 12-month warranty, FAGOR has set up a warranty control system based on having the manufacturer or agent inform FAGOR of the destination, identification and on-machine installation date, by filling out the document accompanying each FAGOR product in the warranty envelope. This system, besides assuring a full year of warranty to the end user, enables our service network to know about FAGOR equipment coming from other countries into their area of responsibility. The warranty starting date will be the one appearing as the installation date on the above mentioned document. FAGOR offers the manufacturer or agent 12 months to sell and install the product. This means that the warranty starting date may be up to one year after the product has left our warehouse so long as the warranty control sheet has been sent back to us. This translates into the extension of warranty period to two years since the product left our warehouse. If this sheet has not been sent to us, the warranty period ends 15 months from when the product left our warehouse. This warranty covers all costs of material and labour involved in repairs at FAGOR carried out to correct malfunctions in the equipment. FAGOR undertakes to repair or replace their products within the period from the moment manufacture begins until 8 years after the date on which it disappears from the catalogue. FAGOR has exclusive competence in deciding whether the repair enters within the term defined as the warranty period. EXCLUDING CLAUSES Repairs will be carried out on our premises. Therefore, all expenses incurred as a result of trips made by technical personnel to carry out equipment repairs, despite these being within the above-mentioned period of warranty, are not covered by the warranty. Said warranty will be applied whenever the equipment has been installed in accordance with instructions, has not be mistreated, has not been damaged by accident or by negligence and has not been tampered with by personnel not authorised by FAGOR. If, once servicing or repairs have been made, the cause of the malfunction cannot be attributed to said elements, the customer is obliged to cover the expenses incurred, in accordance with the tariffs in force. Other warranties, implicit or explicit, are not covered and FAGOR AUTOMATION cannot be held responsible for other damages which may occur. CNC 8037 ·17·
Page 1 and 2: CNC 8037 ·T· Operating manual Ref
Page 3 and 4: Operating manual INDEX About the pr
Page 5 and 6: Operating manual CHAPTER 11 SCREEN
Page 7 and 8: ABOUT THE PRODUCT BASIC CHARACTERIS
Page 9: DECLARATION OF CONFORMITY The manuf
Page 12 and 13: CNC 8037 ·12· Version history
Page 14 and 15: CNC 8037 ·14· Safety conditions P
Page 18 and 19: CNC 8037 ·18· Warranty terms WARR
Page 20 and 21: CNC 8037 ·20· Material returning
Page 22 and 23: CNC 8037 ·22· Additional remarks
Page 24 and 25: CNC 8037 ·24· Fagor documentation
Page 26 and 27: 1. GENERAL CONCEPTS Part programs C
Page 28 and 29: 1. GENERAL CONCEPTS CNC 8037 ·T·
Page 30 and 31: 1. GENERAL CONCEPTS Keyboard layout
Page 32 and 33: 1. GENERAL CONCEPTS Keyboard layout
Page 34 and 35: 1. GENERAL CONCEPTS Layout of the o
Page 36 and 37: 2. OPERATING MODES Help systems CNC
Page 38 and 39: 2. OPERATING MODES CNC 8037 ·T· M
Page 40 and 41: 2. OPERATING MODES CNC 8037 ·T· M
Page 42 and 43: 2. OPERATING MODES CNC 8037 ·42·
Page 44 and 45: 3. OPERATIONS VIA ETHERNET Remote h
Page 46 and 47: 3. OPERATIONS VIA ETHERNET CNC 8037
Page 48 and 49: 3. OPERATIONS VIA ETHERNET CNC 8037
Page 50 and 51: 4. EXECUTE / SIMULATE CNC 8037 ·T
Page 52 and 53: 4. EXECUTE / SIMULATE CNC 8037 ·52
Page 60 and 61: 4. EXECUTE / SIMULATE Display CNC 8
Page 66 and 67:
4. EXECUTE / SIMULATE Display CNC 8
Page 68 and 69:
4. EXECUTE / SIMULATE Display CNC 8
Page 70 and 71:
4. EXECUTE / SIMULATE Tool inspecti
Page 72 and 73:
4. EXECUTE / SIMULATE Tool inspecti
Page 74 and 75:
4. EXECUTE / SIMULATE Graphics CNC
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
4. EXECUTE / SIMULATE Single block
Page 84 and 85:
5. EDIT CNC 8037 ·T· MODEL SOFT:
Page 86 and 87:
Page 88 and 89:
5. EDIT CNC 8037 ·88· Modify ·T
Page 90 and 91:
5. EDIT CNC 8037 ·90· Replace ·T
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
5. EDIT CNC 8037 ·96· Editor para
Page 98 and 99:
5. EDIT CNC 8037 ·98· Editor para
Page 100 and 101:
6. JOG CNC 8037 ·T· MODEL SOFT: V
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
6. JOG CNC 8037 ·114· Spindle mov
Page 116 and 117:
7. TABLES CNC 8037 ·T· MODEL SOFT
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
7. TABLES CNC 8037 ·122· Tool Off
Page 124 and 125:
7. TABLES CNC 8037 ·124· Tool Off
Page 126 and 127:
7. TABLES CNC 8037 ·126· Tool geo
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
7. TABLES CNC 8037 ·132· How to e
Page 134 and 135:
8. UTILITIES CNC 8037 ·T· MODEL S
Page 136 and 137:
8. UTILITIES CNC 8037 ·136· Acces
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
8. UTILITIES CNC 8037 ·142· Acces
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
9. STATUS CNC CNC 8037 ·T· MODEL
Page 150 and 151:
9. STATUS CNC CNC 8037 ·T· MODEL
Page 152 and 153:
9. STATUS DNC CNC 8037 ·T· MODEL
Page 154 and 155:
9. STATUS CAN CNC 8037 ·T· MODEL
Page 156 and 157:
10. PLC CNC 8037 ·T· MODEL SOFT:
Page 158 and 159:
Page 160 and 161:
10. PLC CNC 8037 ·160· Compile ·
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
10. PLC CNC 8037 ·166· Monitoring
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
10. PLC CNC 8037 ·172· Active mes
Page 174 and 175:
10. PLC CNC 8037 ·174· Save progr
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
10. PLC CNC 8037 ·184· Logic anal
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
11. SCREEN EDITOR CNC 8037 ·T· MO
Page 192 and 193:
11. SCREEN EDITOR Utilities CNC 803
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
11. SCREEN EDITOR Texts CNC 8037 ·
Page 202 and 203:
11. SCREEN EDITOR Modifications CNC
Page 204 and 205:
11. SCREEN EDITOR Modifications CNC
Page 206 and 207:
12. MACHINE PARAMETERS CNC 8037 ·2
Page 208 and 209:
12. MACHINE PARAMETERS CNC 8037 ·T
Page 210 and 211:
12. MACHINE PARAMETERS CNC 8037 ·T
Page 212 and 213:
12. MACHINE PARAMETERS CNC 8037 ·2
Page 214 and 215:
13. DIAGNOSIS CNC 8037 ·T· MODEL
Page 216 and 217:
13. DIAGNOSIS Tests CNC 8037 ·T·
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
13. DIAGNOSIS CNC 8037 ·230· Hard
Page 232 and 233:
13. DIAGNOSIS CNC 8037 ·232· Inte
Page 234:
13. CNC 8037 SOFT: V01.4X ·234· O
show all

CNC 8037 T - Operating manual - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?