FS-1030D Service Manual - kyocera

More documents

Recommendations

Info

2G6 (2) Operation panel Figure 1-1-2 1. Ready indicator (Green) 2. Data indicator (Green) 3. Attention indicator (Red) 4. Toner indicator (Red) 5. CANCEL key 6. GO key 1-1-4
2G6 1-1-3 Machine cross section Printer Option paper feeder Paper path Cassette, MP tray Optional paper feeder Switchback and refeed (duplex printing) Figure 1-1-3 1. Cassette 2. Paper feed unit 3. MP tray 4. MP tray paper feed unit 5. Process unit 6. Toner container 7. Transfer section 8. Fuser unit 9. Output tray 10. Conveying section 11. Refeed unit 1-1-5
Page 1 and 2: FS-1030D SERVICE MANUAL Published i
Page 3 and 4: Safety precautions This booklet pro
Page 5 and 6: 1. Installation Precautions WARNING
Page 7 and 8: Do not pull on the AC power cord or
Page 9 and 10: CONTENTS 2G6 1-1 Specifications 1-1
Page 11 and 12: (1-1) Process unit mechanism ......
Page 13 and 14: 2G6-1 1-1-1 Specifications Type ...
Page 15: 2G6 1-1-2 Name of parts (1) Overall
Page 19 and 20: 2G6 1-2-1 Process unit (drum) Note
Page 21 and 22: 2G6 1-3-1 Unpacking and installatio
Page 23 and 24: 2G6 Remove the tape and protective
Page 25 and 26: 2G6 5. Set the toner container into
Page 27 and 28: 2G6 Load paper. 1. Pull the cassett
Page 29 and 30: 2G6 1-3-2 Installing the expanding
Page 31 and 32: 2G6 1-3-4 Installing the network in
Page 33 and 34: 2G6 1-4-1 Maintenance The product i
Page 35 and 36: 2G6 Service items Description Detai
Page 37 and 38: 2G6 Service items Printing an event
Page 39 and 40: 2G6 Service items Description Item
Page 41 and 42: 2G6 Service items Description Items
Page 43 and 44: 2G6 1-5-1 Paper misfeed detection (
Page 45 and 46: 2G6 Code Error indications Contents
Page 47 and 48: 2G6 Check procedures/corrective mea
Page 49 and 50: 2G6 Check procedures/corrective mea
Page 55 and 56: 2G6 (1) No image appears (entirely
Page 57 and 58: 2G6 (6) A black line appears longit
Page 59 and 60: 2G6 (12)Offset occurs. Causes 1. De
Page 61 and 62: 2G6 Problem Causes Check procedures
Page 63 and 64: 2G6 1-5-5 Mechanical problems Probl
Page 65 and 66: 2G6 1-6-1 Precautions for assembly
Page 67 and 68:
2G6 1-6-3 Removing the principal ou
Page 69 and 70:
2G6 1-6-4 Removing the feed roller
Page 71 and 72:
2G6 6. Remove one screw. 7. Remove
Page 73 and 74:
2G6 1-6-7 Removing the principal PW
Page 75 and 76:
2G6 6. Remove two screws at the bac
Page 77 and 78:
2G6 (4) Removing the bias PWB 1. Re
Page 79 and 80:
2G6 1-6-8 Removing the main motor a
Page 81 and 82:
2G6 10. Remove the main PWB (See pa
Page 83 and 84:
2G6 1-6-9 Removing and splitting th
Page 85 and 86:
2G6 (1) Removing the separation cla
Page 87 and 88:
2G6 (3) Removing the heat roller WA
Page 89 and 90:
2G6 (4) Removing the fuser thermist
Page 91 and 92:
2G6 (6) Removing the press roller W
Page 93 and 94:
2G6 4. Remove three screws. 5. Remo
Page 95 and 96:
2G6 1-6-11 Removing the main charge
Page 97 and 98:
2G6 1-7-1 Upgrading the firmware on
Page 99 and 100:
2G6 (3) Downloading the firmware fr
Page 101 and 102:
2G6 2-1-1 Paper feeding system The
Page 103 and 104:
2G6 (2) Paper feeding mechanism
Page 105 and 106:
2G6 Upper exit roller forward/rever
Page 107 and 108:
2G6 (1-1) Process unit mechanism
Page 109 and 110:
2G6 (2-2) Charging the drum The fol
Page 111 and 112:
2G6 (3-1) Laser scanner unit
Page 113 and 114:
(4) Development The latent image co
Page 115 and 116:
(6) Fusing The toner on the paper i
Page 117 and 118:
(7) Cleaning After the transferring
Page 119 and 120:
2G6 2-2-1 Electrical parts layout (
Page 121 and 122:
2G6 2-3-1 Main PWB Xtal(System) CXI
Page 123 and 124:
(1) Eraser lamp control circuit The
Page 125 and 126:
(3) Polygon motor control circuit T
Page 127 and 128:
2G6 Connector Pin No. Signal I/O Vo
Page 129 and 130:
2G6 Connector Pin No. Signal I/O Vo
Page 131 and 132:
2G6 2-3-5 High voltage unit The Hig
Page 133 and 134:
2G6 Timing chart No. 1 Paper casset
Page 135 and 136:
2G6-2 2-4-3 Wiring diagram +24V3 PG
Page 137 and 138:
MEMO:
show all

FS-1030D Service Manual - kyocera

Create successful ePaper yourself

Delete template?

Save as template?