FS-1030D Service Manual - kyocera

More documents

Recommendations

Info

2G6 Unpack. Figure 1-3-1 Unpacking 1. Printer 2. Power cord 3. Installation guide 4. Toner container 5. Cleaning cloth 6. CD-ROMs 7. Extension tray [For inch model only] 1-3-2
2G6 Remove the tape and protective packing 1. Remove the two tape. Tape Figure 1-3-2 2. Pull the cassette out of the printer. 3. Remove the protective packing from inside the cassette. Protective packing Cassette Figure 1-3-3 1-3-3
Page 1 and 2: FS-1030D SERVICE MANUAL Published i
Page 3 and 4: Safety precautions This booklet pro
Page 5 and 6: 1. Installation Precautions WARNING
Page 7 and 8: Do not pull on the AC power cord or
Page 9 and 10: CONTENTS 2G6 1-1 Specifications 1-1
Page 11 and 12: (1-1) Process unit mechanism ......
Page 13 and 14: 2G6-1 1-1-1 Specifications Type ...
Page 15 and 16: 2G6 1-1-2 Name of parts (1) Overall
Page 17 and 18: 2G6 1-1-3 Machine cross section Pr
Page 19 and 20: 2G6 1-2-1 Process unit (drum) Note
Page 21: 2G6 1-3-1 Unpacking and installatio
Page 25 and 26: 2G6 5. Set the toner container into
Page 27 and 28: 2G6 Load paper. 1. Pull the cassett
Page 29 and 30: 2G6 1-3-2 Installing the expanding
Page 31 and 32: 2G6 1-3-4 Installing the network in
Page 33 and 34: 2G6 1-4-1 Maintenance The product i
Page 35 and 36: 2G6 Service items Description Detai
Page 37 and 38: 2G6 Service items Printing an event
Page 39 and 40: 2G6 Service items Description Item
Page 41 and 42: 2G6 Service items Description Items
Page 43 and 44: 2G6 1-5-1 Paper misfeed detection (
Page 45 and 46: 2G6 Code Error indications Contents
Page 47 and 48: 2G6 Check procedures/corrective mea
Page 49 and 50: 2G6 Check procedures/corrective mea
Page 55 and 56: 2G6 (1) No image appears (entirely
Page 57 and 58: 2G6 (6) A black line appears longit
Page 59 and 60: 2G6 (12)Offset occurs. Causes 1. De
Page 61 and 62: 2G6 Problem Causes Check procedures
Page 63 and 64: 2G6 1-5-5 Mechanical problems Probl
Page 65 and 66: 2G6 1-6-1 Precautions for assembly
Page 67 and 68: 2G6 1-6-3 Removing the principal ou
Page 69 and 70: 2G6 1-6-4 Removing the feed roller
Page 71 and 72: 2G6 6. Remove one screw. 7. Remove
Page 73 and 74:
2G6 1-6-7 Removing the principal PW
Page 75 and 76:
2G6 6. Remove two screws at the bac
Page 77 and 78:
2G6 (4) Removing the bias PWB 1. Re
Page 79 and 80:
2G6 1-6-8 Removing the main motor a
Page 81 and 82:
2G6 10. Remove the main PWB (See pa
Page 83 and 84:
2G6 1-6-9 Removing and splitting th
Page 85 and 86:
2G6 (1) Removing the separation cla
Page 87 and 88:
2G6 (3) Removing the heat roller WA
Page 89 and 90:
2G6 (4) Removing the fuser thermist
Page 91 and 92:
2G6 (6) Removing the press roller W
Page 93 and 94:
2G6 4. Remove three screws. 5. Remo
Page 95 and 96:
2G6 1-6-11 Removing the main charge
Page 97 and 98:
2G6 1-7-1 Upgrading the firmware on
Page 99 and 100:
2G6 (3) Downloading the firmware fr
Page 101 and 102:
2G6 2-1-1 Paper feeding system The
Page 103 and 104:
2G6 (2) Paper feeding mechanism
Page 105 and 106:
2G6 Upper exit roller forward/rever
Page 107 and 108:
2G6 (1-1) Process unit mechanism
Page 109 and 110:
2G6 (2-2) Charging the drum The fol
Page 111 and 112:
2G6 (3-1) Laser scanner unit
Page 113 and 114:
(4) Development The latent image co
Page 115 and 116:
(6) Fusing The toner on the paper i
Page 117 and 118:
(7) Cleaning After the transferring
Page 119 and 120:
2G6 2-2-1 Electrical parts layout (
Page 121 and 122:
2G6 2-3-1 Main PWB Xtal(System) CXI
Page 123 and 124:
(1) Eraser lamp control circuit The
Page 125 and 126:
(3) Polygon motor control circuit T
Page 127 and 128:
2G6 Connector Pin No. Signal I/O Vo
Page 129 and 130:
2G6 Connector Pin No. Signal I/O Vo
Page 131 and 132:
2G6 2-3-5 High voltage unit The Hig
Page 133 and 134:
2G6 Timing chart No. 1 Paper casset
Page 135 and 136:
2G6-2 2-4-3 Wiring diagram +24V3 PG
Page 137 and 138:
MEMO:
show all

FS-1030D Service Manual - kyocera

Create successful ePaper yourself

Delete template?

Save as template?