BK-7m_OM.pdf - Roland

More documents

Recommendations

Info

Backing Module BK-7m Menu options r 58 Parameter Setting Explanation Pre LPF 0~7 Cuts the high frequency range of the sound coming into the chorus. Higher values will cut more of the high frequencies. Level 0~127 Output level of the chorus signal. Feedback 0~127 Adjusts the amount of the chorus sound that is fed back into the effect. Delay 0~127 Adjusts the delay time from the direct sound until the chorus sound is heard. Rate 0~127 This parameter sets the speed (frequency) at which the chorus sound is modulated. Higher values result in faster modulation. Depth 0~127 This parameter sets the depth at which the chorus sound is modulated. Higher values result in a more pronounced modulation. Reverb Send 0~127 This parameter sets the amount of chorus sound that is sent to the Reverb processor. The value “127” effectively allows you to connect the chorus and reverb effects in series (Chorus before Reverb). If you do not want the chorus signal to be processed by the Reverb effect, set this value to “0”. Parameters for the “6. Delay” type: Parameter Setting Explanation Level 0~127 Output level of the chorus signal. Parameter Setting Explanation Output Select Main, Rev, Main+Rev Allows you to specify where the processor’s output signal should go: to the OUTPUT sockets (“Main”), the Reverb processor (“Rev”) or both (“Main+Rev”). The latter two options mean that the chorus signal is also processed by the reverb effect you select. L Delay Sync msec, Note Use this parameter to specify whether (“Note”) or not (“msec”) the delay time should be synchronized to the tempo. Depending on your choice, the setting range of the following parameter refers to a time (msec) or a note value. L Delay msec 0~1000ms Specifies the delay time. This can be either a time value (“msec”) or a note value, depending on how you set the “Delay Sync” parameter above. “T” means “triplet” and a L Delay Note 1/64T, 1/64, 1/32T, 1/32, 1/16T, 1/32., 1/16, 1/8T, 1/16., 1/8, 1/4T, 1/8., 1/4, 1/2T, 1/4., 1/2, 1/1T, 1/2., 1/1, 2/1T, 1/1., 2/1 “.” refers to a dotted note. “2/1” means that each repetition comes after two measures/ bars. The advantage of working with a note value is that the delay effect always runs in sync with the current tempo. L Level 0~127 Volume of each delay line (there are three – left, center and right). HF Damp C Delay Sync C Delay msec C Delay Note C Level 200~8000Hz, Bypass See “L Delay Sync” See “L Delay msec” See “L Delay Note” See “L Level” Adjusts the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies, set this parameter to BYPASS.
Backing Module BK-7m r ‘Performance Edit’ parameters Parameter Setting Explanation C Feedback –98~+98% Adjusts the proportion of the delay sound that is fed back into the effect. Negative (–) settings invert the phase. R Delay Sync R Delay msec R Delay Note R Level See “L Delay Sync” See “L Delay msec” See “L Delay Note” See “L Level” ‘Style Parts’ parameters This function group can be selected using [MENU] button ‰ “Performance Edit” ‰ “Style Parts”. Exp. Pedal Select “Off” if you don’t need pedal expression for the selected part. This means that the Music Style part in question no longer responds to an expression pedal you may have connected to the SWITCH/EXPRESSION socket. Parameter Exp. Pedal Setting Off, On Exp. Pedal All Parts On If you are not sure which Music Style parts still receive expression messages, and if you want all to receive them, you can select this field and press the [CURSOR÷VALUE] dial. Exp. Pedal All Parts Off If you are not sure which Music Style parts still receive expression messages, and if no Music Style part should receive them, you can select this field and press the [CURSOR÷VALUE] dial. The parameters of this function group apply to the eight Arranger parts (i.e. the parts used to play back the selected Music Style). 1. Use the [CURSOR÷VALUE] dial to select the Music Style part you want to edit (ADrum, ABass, Acc1, Acc2, Acc3, Acc4, Acc4, Acc5, Acc6). The display shows the settings for the selected part. 2. Use the dial to select and set the desired parameter(s) The following parameters are available: Mute Allows you to mute the selected part, so that it is no longer audible. Parameter Mute Solo Allows you to solo the selected part, which means that all other Music Style parts are switched off. Parameter Solo Setting Off, On Explanation Volume Adjusts the volume of the selected Music Style part. Selecting “0” means that the part is question is no longer audible. Parameter Off, On Setting Volume 0~127 Split This page allows you to set two keyboard-related parameters. It can be selected using [MENU] button ‰ “Performance Edit” ‰ “Split”. Split Point The “Split Point” parameter allows you to set the split point. Parameter Split Point Lower Hold This parameter allows you to set the Hold function for the LWR part. Parameter Lower Hold Setting B1~B6 Setting Off, On If you set this parameter to “On”, the notes of the LWR part go on sounding until you play other notes in the left keyboard area. (This function is only available while the [SPLIT] button lights.) If you select “Off”, the LWR part stops sounding as soon as you release all keys in the left area. Key This function allows you to transpose the BK-7m’s pitch in semi-tone steps. Depending on the mode setting, this transposition applies to all sections or just a specific section. It can be selected using [MENU] button ‰ “Performance Edit” ‰ “Key” or by pressing the [KEY] button. See “Changing the key” on p. 37. 59
Page 1 and 2:
Owner’s Manual r
Page 3 and 4:
Owner’s Manual Thank you and cong
Page 5 and 6:
Backing Module BK-7m r Using the un
Page 7 and 8: Backing Module BK-7m r Important no
Page 9 and 10: Backing Module BK-7m r Contents 1.
Page 11 and 12: Backing Module BK-7m r Panel descri
Page 13 and 14: Backing Module BK-7m r Rear panel R
Page 15 and 16: Backing Module BK-7m r Before you s
Page 17 and 18: Backing Module BK-7m r Connecting t
Page 19 and 20: Backing Module BK-7m r Listening th
Page 21 and 22: Backing Module BK-7m r Basic operat
Page 23 and 24: Backing Module BK-7m r Details abou
Page 25 and 26: Backing Module BK-7m r Details abou
Page 27 and 28: Backing Module BK-7m r Playing the
Page 29 and 30: Backing Module BK-7m r Selecting To
Page 31 and 32: Backing Module BK-7m r Using Music
Page 33 and 34: Backing Module BK-7m r Playing back
Page 35 and 36: Backing Module BK-7m r Using the BK
Page 37 and 38: Backing Module BK-7m r Other import
Page 39 and 40: Backing Module BK-7m r Using Split
Page 41 and 42: Backing Module BK-7m r Performance
Page 43 and 44: Backing Module BK-7m r Saving your
Page 45 and 46: Backing Module BK-7m r Other Perfor
Page 47 and 48: Backing Module BK-7m r Recording Li
Page 49 and 50: Backing Module BK-7m r Saving your
Page 51 and 52: Backing Module BK-7m r ‘Performan
Page 57: Backing Module BK-7m r ‘Performan
Page 63 and 64: Backing Module BK-7m r ‘Global’
Page 65 and 66: Backing Module BK-7m r ‘Global’
Page 67 and 68: Backing Module BK-7m r MIDI paramet
Page 69 and 70: Backing Module BK-7m r MIDI paramet
Page 71 and 72: Backing Module BK-7m r Mastering To
Page 73 and 74: Backing Module BK-7m r Mastering To
Page 75 and 76: Backing Module BK-7m r Makeup Tools
Page 83 and 84: Backing Module BK-7m r Factory Rese
Page 85 and 86: Backing Module BK-7m r Troubleshoot
Page 87 and 88: Backing Module BK-7m r ‘Wizard Co
Page 89 and 90: Backing Module BK-7m r Music Style
Page 91 and 92: Backing Module BK-7m r Tone List 20
Page 93 and 94: Backing Module BK-7m r Tone List Vo
Page 95 and 96: Backing Module BK-7m r Tone List CC
Page 97 and 98: Backing Module BK-7m r Drum Sets C-
Page 99 and 100: Backing Module BK-7m r Drum Sets C-
Page 101 and 102: Backing Module BK-7m r Drum Sets PC
Page 103 and 104: Backing Module BK-7m r Drum Sets PC
Page 105 and 106: Backing Module BK-7m r Specificatio
Page 107 and 108: Backing Module BK-7m r MFX types an
Page 109 and 110:
Backing Module BK-7m r MFX types an
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Backing Module BK-7m r Index Numeri
Page 125 and 126:
Backing Module BK-7m r T Tap Tempo
Page 127 and 128:
For EU Countries For China China
show all

BK-7m_OM.pdf - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?