maxon

More documents

Recommendations

Info

Spindle Drive Optionsmaxon spindle driveOption to GP 16 S to GP 22 SSpecial lengthOrder reference SPIN01Without specification, the spindle is supplied in the standardlength 102 mm. Special lengths can be ordered in 5 mm stepsup to the stated maximum length.Without specification, the spindle is supplied in the standardlength 151 mm. Special lengths can be ordered in 5 mm stepsup to the stated maximum length.Spindle endOrder reference SPIN02In order to support the end of thespindle by an additional bearing, itcan be delivered according to theillustration.Customer specific spindle ends onrequest.-0.006-0.0204Ø3-0.004-0.0125Ø4Flange nutOrder reference SPIN0418 * 1460°4 x Ø3.4-0.006-0.017Ø1260°4 x Ø3.4Ø24-0.015 *1-0.030Ø10-0.006 *2-0.017Ø1220 * 2 Ø18Flange nut instead of the standardthread nut.Ø24If using a ball screw, the rectangularmounting flange (SPIN 06) must beused.* 1 Kugelumlaufspindel / Ball Screw* 2 Metrische Spindel / Metric Spindle16184 16Ø18Low backlash ball screw nutOrder reference SPIN05Not available for GP 16 S.Axial play is almost eliminated through increased pre-loadingof the ball screw nut. Although, the increased load can lead togreater wear.Rectangular mounting flangeOrder reference SPIN063.3 0 – 0.61.9 + 0.35 – 0.20Ø16 – 0.10Ansicht ohne Mutter/view without nut02.9 - 0.11.4 ± 0.050Ø25 h7 ( - 0.021 )Ansicht ohne Mutter/view without nutSpindle drive with rectangular mountingflange allows mounting from thegearhead side.Ø3.3Ø6.5 x 2.4If using a ball screw with flange nut,the rectangular assembly flange mustbe used for mounting.Ø10 – 0.0101520Ø2.70Ø25 h7 ( - 0.021)46.22330258maxon spindle driveMay 2012 edition / subject to change
Spindle Drive OptionsOptionSpecial lengthOrder reference SPIN01to GP 32 SWithout specification, the spindle is supplied in the standardlength 200.8 mm. Special lengths can be ordered in 5 mm stepsup to the stated maximum length.maxon spindle driveSpindle endOrder reference SPIN02In order to support the end of thespindle by an additional bearing, itcan be delivered according to theillustration.-0.004-0.012Ø6Customer specific spindle ends onrequest.1060°Flange nutOrder reference SPIN04-0.006-0.017Ø184 x Ø4.5Flange nut instead of the standardthread nut.Ø35If using a ball screw, the rectangularmounting flange (SPIN 06) must beused.285 22Ø27Low backlash ball screw nutOrder reference SPIN05Axial play is almost eliminated through increased pre-loadingof the ball screw nut. Although, the increased load can lead togreater wear.Rectangular mounting flangeOrder reference SPIN0602.95 - 0.1(Gewindeauslauf/thread run out)2 ±0.050Ø36 h7 ( - 0.025 )Ansicht ohne Mutter/view without nutSpindle drive with rectangular mountingflange allows mounting from thegearhead side.Ø4.2Ø8 x 3If using a ball screw with flange nut,the rectangular assembly flange mustbe used for mounting.0Ø36 h7 ( - 0.025 )69.631.540May 2012 edition / subject to changemaxon spindle drive259
Page 1 and 2:
Program 2012/13High Precision Drive
Page 3:
Welcome to 4-15maxon motormaxon sel
Page 6 and 7:
maxon manufacturing company in Germ
Page 8 and 9:
Develop,Automate,Test.8
Page 10 and 11:
maxonQuality AssuranceOne of maxon
Page 12:
Where are maxonmotors used today?Ou
Page 15 and 16:
maxon sensorEncoders, DC tachos and
Page 17 and 18:
Selection Guidemaxon gear / maxon s
Page 19 and 20:
GearsGS 12 A 208GP 13 K 209GP 13 A
Page 21:
GearsGS 12 A 208GP 13 K 209GP 13 A
Page 24 and 25:
maxon DC motormaxon DC motorTechnol
Page 26 and 27:
maxon EC motormaxon EC motor ironle
Page 28 and 29:
maxon EC motormaxon EC motor iron-c
Page 30 and 31:
maxon gearTechnology - short and to
Page 32 and 33:
maxon sensorTechnology - short and
Page 34 and 35:
maxon motor controlmaxon motor cont
Page 36 and 37:
maxon DC motor and maxon EC motorKe
Page 38 and 39:
Motor diagrams, operating rangesmax
Page 40 and 41:
Tolerancesmaxon motorTolerances mus
Page 42 and 43:
maxon motorRegulated servo drivesIn
Page 44 and 45:
maxon e-mediamaxon motorVisit us on
Page 46 and 47:
maxon Conversion Tablesmaxon motorG
Page 48 and 49:
maxon Standard Specificationmaxon D
Page 50 and 51:
maxon DC motorRE 6 6 mm, Precious M
Page 52 and 53:
maxon DC motorRE 10 10 mm, Precious
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
maxon DC motorRE 13 13 mm, Graphite
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
maxon A-max programThe economically
Page 88 and 89:
maxon DC -max motor-max 12 12 mm, P
Page 90 and 91:
Page 92 and 93:
maxon DC -max motor-max 16 16 mm, G
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
maxon RE-max programThe high-power
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
maxon Standard Specificationmaxon E
Page 138 and 139:
maxon EC motorEC 6 6 mm, brushless,
Page 140 and 141:
maxon EC motorEC 10 10 mm, brushles
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
maxon EC-max programThe “heart”
Page 164 and 165:
maxon -max-max 16 2-wire 16 mm, bru
Page 166 and 167:
maxon -max-max 22 22 mm, brushless,
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
For your personal notesmaxon motorP
Page 174 and 175:
maxon EC-4pole programThe “heart
Page 176 and 177:
maxon EC -4pole motor-4pole 22 22 m
Page 178 and 179:
maxon EC -4pole motor-4pole 30 30 m
Page 180 and 181:
maxon flat motorEC 9.2 flat 10 mm,
Page 182 and 183:
maxon flat motorEC 14 flat 13.6 mm,
Page 184 and 185:
maxon flat motorEC 20 flat 20 mm, b
Page 186 and 187:
maxon flat motorEC 20 flat brushles
Page 188 and 189:
Page 190 and 191:
maxon flat motor-i 40 40 mm, brushl
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
maxon flat motorEC 45 flat brushles
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
maxon Standard Specificationmaxon g
Page 204 and 205:
Planetary Gearhead GP 6 A 6 mm, 0.0
Page 206 and 207:
maxon gearPlanetary Gearhead GP 10
Page 208 and 209: Spur Gearhead GS 12 A 12 mm, 0.01-0
Page 210 and 211: Planetary Gearhead GP 13 A 13 mm, 0
Page 212 and 213: maxon gearSpur Gearhead GS 16 K 16
Page 214 and 215: maxon gearSpur Gearhead GS 16 V 16
Page 216 and 217: maxon gearPlanetary Gearhead GP 16
Page 218 and 219: Planetary Gearhead GP 16 C 16 mm, 0
Page 220 and 221: Planetary Gearhead GP 19 B 19 mm, 0
Page 222 and 223: Planetary Gearhead GP 22 B 22 mm, 0
Page 230 and 231: Spur Gearhead GS 24 A 24 mm, 0.1 Nm
Page 240 and 241: maxon gearKoaxdrive KD 32 32 mm, 1.
Page 244 and 245: Spur Gearhead GS 45 A 45 mm, 0.5-2.
Page 250 and 251: Spindle Drive Basicsmaxon spindle d
Page 252 and 253: Spindle Drive GP 16 S Ø16 mm, Metr
Page 260 and 261: For your personal notesmaxon motorP
Page 262 and 263: Encoder MILE 64 Counts per turn, 3
Page 264 and 265: Encoder MILE 800-3200 CPT, 2 Channe
Page 266 and 267: Encoder MR Type S, 64-256 CPT, 2 Ch
Page 268 and 269: Encoder MR Type M, 32 Counts per tu
Page 270 and 271: Encoder MR Type M, 128-512 CPT, 2/3
Page 272 and 273: Encoder MR Type ML, 128-1000 CPT, 3
Page 274 and 275: Encoder Enc 22 100 Counts per turn,
Page 276 and 277: Encoder HEDS 5540 500 Counts per tu
Page 278 and 279: Encoder HEDL 5540 500 CPT, 3 Channe
Page 284 and 285: Encoder MEnc 13 16 Counts per turn,
Page 286 and 287: DC-Tacho DCT 22 0.52 Voltmaxon sens
Page 288 and 289: For your personal notesmaxon motorP
Page 290 and 291: ESCON Overviewmaxon motor controlTh
Page 292 and 293: ESCON Feature Comparison Chartmaxon
Page 294 and 295: DECS 50/5 1-Q-EC Amplifier, sensorl
Page 296 and 297: DEC Module 50/5 1-Q-EC Amplifiermax
Page 298 and 299: 1-Q-EC Amplifier Datamaxon motor co
Page 300 and 301: 1-Q-EC Amplifier Dimensions and con
Page 302 and 303: 4-Q-EC Amplifier Summarymaxon motor
Page 304 and 305: DES 50/5 4-Q-EC Servoamplifiermaxon
Page 306 and 307: 4-Q-EC Servoamplifier Datamaxon mot
Page 308 and 309:
4-Q-EC Servoamplifier Dimensions an
Page 310 and 311:
maxon motor controlEPOS2 Positionin
Page 312 and 313:
EPOS2 Positioning control unit Data
Page 314 and 315:
EPOS2 P programmable positioning co
Page 316 and 317:
EPOS2 P programmable positioning co
Page 318 and 319:
maxon motor controlPoint to pointTh
Page 320 and 321:
Summary maxon motor controlmaxon mo
Page 322 and 323:
Summary maxon motor control accesso
Page 324 and 325:
MCD EPOS Intelligent compact drivem
Page 326 and 327:
ProgrammingAccessories MCD EPOS 60
Page 328 and 329:
Brake AB 20 24 VDC, 0.1 Nmmaxon acc
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Accessories overviewmaxon accessori
Page 338 and 339:
Page 340 and 341:
maxon special programRE 15 15 mm, P
Page 342 and 343:
maxon special programF 2130 30 mm,
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
maxon special programS 2322 22 mm,
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
maxon special programA 2515 15 mm,
Page 358 and 359:
GM 20 20 mm, Precious Metal Brushes
Page 360 and 361:
EC 16 16 mm, brushless, 40 Wattmaxo
Page 362 and 363:
maxon special programEC 22 22 mm, b
Page 364 and 365:
EC 22 22 mm, brushless, 50 Watt, st
Page 366 and 367:
maxon maxon special -4pole program-
Page 368 and 369:
EC 90 flat brushless, 60 Watt, with
Page 370 and 371:
4-Q-DC Servoamplifier Summarymaxon
Page 372 and 373:
4-Q-DC Servoamplifier Datamaxon spe
Page 374 and 375:
4-Q-DC Servoamplifier Dimensions an
Page 376 and 377:
maxon special designmaxon special d
Page 378 and 379:
maxon special designmaxon special d
Page 380 and 381:
Page 382 and 383:
maxon ceramic - Innovative CIM / MI
Page 384 and 385:
MIM technology — Complex Shapes i
Page 386 and 387:
maxon Manufacturing Companiesmaxon
Page 388 and 389:
Americamaxon Sales CompaniesUSA (Ea
Page 390:
maxon product rangeThe solution is
show all

maxon

Create successful ePaper yourself

Delete template?

Save as template?