You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
03<br />
Connecting digital<br />
components<br />
The easiest way to hook up this<br />
receiver for surround sound is to<br />
use a digital input. You can do this<br />
by either coaxial or optical connections<br />
(you do not need to do both).<br />
The quality of these two types of<br />
connections is the same but since<br />
some digital components only<br />
have one type of digital terminal, it<br />
is a matter of matching like with<br />
like (for example, the coaxial<br />
output from the<br />
component to coaxial input on the<br />
receiver). The VSX-D711 has three<br />
digital inputs on the rear panel<br />
(two coaxial inputs and a optical<br />
input) and the VSX-D811S has four<br />
(two coaxial inputs and two optical<br />
inputs). Connect your digital<br />
components to the rear panel as<br />
shown right page. See page 25 to<br />
connect the front panel optical<br />
input on the VSX-D811S.<br />
There is one digital output jack<br />
which is marked DIGITAL OUT. If<br />
you connect this to the optical<br />
input on a digital recorder (currently<br />
these include MD, DAT and<br />
CD-R) you can make direct digital<br />
recordings with this unit.<br />
When connecting your equipment,<br />
always make sure the power is<br />
turned off and the power cord is<br />
disconnected from the AC wall<br />
outlet.<br />
If you have an LD player, you<br />
need to make special connections<br />
to ensure you can play<br />
2 RF format LDs on your<br />
system. If this is the case,<br />
hook up your DVD or LD player<br />
directly to an RF demodulator<br />
using both the 2RF output<br />
and either a coaxial or optical<br />
digital connection. VHalso<br />
recommend hooking up your<br />
digital components to analog<br />
audio jacks as well. Make sure<br />
the RF demodulator digital in<br />
switch is set correctly (optical<br />
or coaxial depending on the<br />
connection). See the component's<br />
instruction manual if<br />
20 you are unsure about its input<br />
and output jacks.<br />
En/Sp/ChH<br />
Conexión de<br />
componentes digitales<br />
La mejor manera de conectar este<br />
receptor para un sonido surround es<br />
utilizar una entrada digital. Podrá<br />
hacerlo mediante una conexión<br />
coaxial u óptica (no es necesario que<br />
haga ambas). La calidad de estos<br />
dos tipos de conexiones es la misma,<br />
pero debido a que algunos<br />
componentes digitales sólo disponen<br />
de un tipo de terminal digital, es<br />
necesario hacerlos corresponder (por<br />
ejemplo, la salida coaxial del<br />
componente a la entrada coaxial del<br />
receptor).<br />
El VSX-D711 dispone de tres<br />
entradas digitales en la parte<br />
posterior del panel (dos entradas<br />
coaxiales y una entrada óptica),<br />
mientras que el VSX-D811S dispone<br />
de cuatro (dos entradas coaxiales y<br />
dos entradas ópticas). Conecte los<br />
componentes digitales al panel<br />
posterior tal y como se muestra en la<br />
derecha págine. Véase la página 25<br />
para conectar la entrada óptica del<br />
panel en el VSX-D811S.<br />
Hay una toma de salida digital<br />
marcada como DIGITAL OUT. Si la<br />
conecta a la toma óptica de una<br />
grabadora digital (normalmente<br />
incluyen MD, DAT y CD-R) puede<br />
hacer grabaciones digitales directas<br />
con este aparato.<br />
Cuando conecte el equipo, asegúrese<br />
siempre de que está apagado y el<br />
cable de alimentación desconectado<br />
de la toma de CA.<br />
Nota<br />
Si dispone de un reproductor de<br />
LDs, será necesario que haga<br />
conexiones especiales para<br />
asegurarse de que puede<br />
reproducir LDs con formato 2<br />
RF en su sistema. Si este es el<br />
caso, conecte el reproductor de<br />
DVDs o LDs directamente a un<br />
demodulador RF utilizando la<br />
salida 2 RF y una conexión<br />
digital coaxial u óptica. También<br />
le recomendamos conectar los<br />
componentes digitales a tomas<br />
de audio analógicas. Asegúrese<br />
de que el interruptor DIGITAL IN<br />
del demodulador RF está<br />
ajustado correctamente (óptica<br />
o coaxial, dependiendo de la<br />
conexión). Consulte el manual<br />
de instrucciones del<br />
componente en caso de que<br />
tenga dudas acerca de las<br />
tomas de entrada y salida.<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
DIGITAL OUT<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
2<br />
2