Bid #01-1112 Library and Reprographics Roofing ... - Citrus College

More documents

Recommendations

Info

Siplast PA-917 LS Primer by Siplast; Irving, TX 2. Primer for Self-Adhesive Flashing Reinforcing Sheets: A quick drying, low-VOC, water-based, high-tack primer specifically designed to promote adhesion of roofing and waterproofing sheets to approved substrates. Primer shall meet South Coast Air Quality District and Ozone Transport Commission requirements. > Siplast TA-119 Primer by Siplast; Irving, TX 3. Mastics: An asphalt cutback mastic, reinforced with non-asbestos fibers, used as a base for setting metal flanges conforming to ASTM D 4586 Type II requirements. > Siplast PA-1021 Plastic Cement by Siplast; Irving, TX B. PMMA Primers 1. Primer for Vertical Concrete and Masonry Substrates: A fast-curing PMMA-based primer for use in vertical applications over concrete, concrete repair materials and masonry substrates. > Pro Primer W by Siplast; Irving, TX 2. Primer for Wood, Plywood and Rigid Insulation Substrates: A fast-curing PMMAbased primer for use in over wood, plywood and rigid insulation substrates. > Pro Primer W by Siplast; Irving, TX C. Sealant: A moisture-curing, non-slump elastomeric sealant designed for roofing applications. The sealant shall be approved by the roof membrane manufacturer for use in conjunction with the roof membrane materials. Acceptable types are as follows: > Siplast PS-304 Elastomeric Sealant by Siplast; Irving, TX D. Synthetic Chips: Synthetic chips to match the factory applied reflective surfacing of the finish ply. E. Resin Accessories 1. Cleaning Solution/Solvent: A clear solvent used to clean and prepare transition areas of in-place catalyzed resin to receive subsequent coats of resin and to clean substrate materials to receive resin. > Pro Prep by Siplast; Irving, TX 2. Preparation Paste: A PMMA based paste used for remediation of depressions in substrate surfaces or other irregularities. > Pro Paste Resin by Siplast; Irving, TX F. Perlite Cant Strips: A cant strip composed of expanded volcanic minerals combined with waterproofing binders. The top surface shall be pre-treated with an asphalt based coating. The face of the cant shall have a nominal 4 inch dimension. G. Fasteners M-13-135 page - 12 Citrus Library Roofing Specification
1. Insulation Fasteners: Insulation fasteners and plates shall be FM Approved, and/or approved by the manufacturer of the primary roofing products. The insulation fasteners shall provide attachment required to meet the specified uplift performance and to restrain the insulation panels against the potential for ridging. The fastening pattern for each insulation panel to be used shall be as recommended by the insulation manufacturer and approved by the manufacturer of the primary roofing products. Acceptable insulation fastener manufacturers for specific deck types are listed below. a) Metal Decks: Insulation mechanical fasteners for metal decks shall be factory coated for corrosion resistance. The fastener shall conform meet or exceed Factory Mutual Standard 4470 and when subjected to 30 Kesternich cycles, show less than 15% red rust. Acceptable insulation fastener types for metal decks are listed below. - A fluorocarbon coated screw type roofing fastener having a minimum 0.220 inch thread diameter. Plates used in conjunction with the fastener shall be a metal type having a minimum 3 inch diameter, as supplied by the fastener manufacturer. > Parafast Fastener by Siplast; Irving, TX > Roofgrip with Buildex Metal Plates by ITW Buildex; Itasca, IL > Dekfast #12 with Dekfast Steel Hexagonal Plates by Construction Fasteners, Inc.; Wyomissing, PA > Standard Roofing Fastener by OMG; Agawam, MA 2. Flashing Reinforcing Sheet Fasteners for Wood/Plywood Substrates to Receive Flashing Coverage: Fasteners shall be approved by the manufacturer of the primary roofing products. Acceptable fasteners for specific substrate types are listed below. a) Wood/Plywood Substrates - A 12 gauge, spiral or annular threaded shank, zinc coated steel roofing fastener having a minimum 1 inch head. > Square Cap by W.H. Maze Co.; Peru, IL > 12 Gauge Simplex Nail by the Simplex Nail and Manufacturing Co., Americus, GA 3. Wood Nailer Fasteners Wood blocking fasteners and plates shall be FM Approved, and/or approved by the manufacturer of the primary roofing products. Acceptable fastener manufacturers are listed below. a) Wood Blocking: Mechanical fasteners for wood blocking shall be factory coated for corrosion resistance. Acceptable fastener types are listed below. - A fluorocarbon coated screw type roofing fastener having a minimum 0.220 inch thread diameter. Plates used in conjunction with the fastener shall be a metal type having a minimum 3 inch diameter, as supplied by the fastener manufacturer. > Parafast Fastener by Siplast; Irving, TX > Roofgrip with Buildex Metal Plates by ITW Buildex; Itasca, IL M-13-135 page - 13 Citrus Library Roofing Specification
Page 1 and 2:
Bid #01-1112 Library and Reprograph
Page 3 and 4:
NOTICE TO CONTRACTORS CALLING FOR B
Page 5 and 6:
Preparation and Submittal of Bid Pr
Page 7 and 8:
District's Right to Modify Contract
Page 9 and 10:
Job-Walk Proposals must be held ope
Page 11 and 12:
documents submitted in response to
Page 13 and 14:
Purchasing Office located at 1000 W
Page 15 and 16:
acknowledges that the District may,
Page 17 and 18:
SUBCONTRACTORS LIST Bidder: _______
Page 19 and 20:
___________________________________
Page 21 and 22:
5.1.2 Are there any judgments, orde
Page 23 and 24:
Executed this ________ day of _____
Page 25 and 26:
IN WITNESS WHEREOF, the Principal a
Page 27 and 28:
AGREEMENT THIS AGREEMENT is made th
Page 29 and 30:
LABOR AND MATERIAL PAYMENT BOND KNO
Page 31 and 32:
PERFORMANCE BOND KNOW ALL MEN BY TH
Page 33 and 34:
CERTIFICATE OF WORKERS' COMPENSATIO
Page 35 and 36:
5. Contractor and I acknowledge tha
Page 37 and 38:
The undersigned individual executin
Page 39 and 40:
6.1 Workers' Compensation Insurance
Page 41 and 42:
GENERAL CONDITIONS ARTICLE 1: DEFIN
Page 43 and 44:
equipment or workmanship forming a
Page 45 and 46:
3.1.4 Verification of Applications
Page 47 and 48:
actual or potential impact of any s
Page 49 and 50:
coordination of the Work and compon
Page 51 and 52:
superintendent shall represent the
Page 53 and 54:
Contract Time or the Contract Price
Page 55 and 56:
4.10 Safety limitation, orders for
Page 57 and 58:
4.11.5 Compliance with Proposition
Page 59 and 60:
4.21.2 Payment of Prevailing Rates.
Page 61 and 62:
eight (8) hours in any calendar day
Page 63 and 64:
that such person hold a valid contr
Page 65 and 66:
performed, whether such operations
Page 67 and 68:
6.8 Indemnity. Unless arising solel
Page 69 and 70:
7.3.1 Submittal of Preliminary Cons
Page 71 and 72:
hereinabove. The District's electio
Page 73 and 74:
or Final Completion, the Work is ac
Page 75 and 76:
Payment pursuant to the preceding s
Page 77 and 78:
following, the submittal of which a
Page 79 and 80:
(xxi) Failure to properly pay preva
Page 81 and 82:
failure, for any reason, to give wr
Page 83 and 84:
shall constitute full compensation
Page 85 and 86:
with the performance of such item o
Page 87 and 88: tests, inspections or approvals rev
Page 89 and 90: of the Contractor under the Contrac
Page 91 and 92: 15.1.7 Conversion to Termination fo
Page 93 and 94: SPECIAL CONDITIONS 1. Application o
Page 95 and 96: REQUEST FOR SUBSTITUTION FORM Failu
Page 97 and 98: CERTIFICATION OF EQUAL PERFORMANCE
Page 99 and 100: W-9 Form (Rev. October 2007) Depart
Page 101 and 102: Form W-9 (Rev. 10-2007) Generally,
Page 103 and 104: Citrus College Citrus Community Col
Page 105 and 106: Roofing Specification For: Citrus C
Page 107 and 108: The basic work descriptions (compon
Page 109 and 110: 7. Duct systems shall not be pressu
Page 111 and 112: 1. Letter from the proposed primary
Page 113 and 114: 3. Limited Access: Prevent access b
Page 115 and 116: 2. Self-Adhesive Modified Bitumen F
Page 117 and 118: 1. Insulation Fasteners: Insulation
Page 119 and 120: metal edge fascia with 1 foot secti
Page 121 and 122: fastening should be provided at all
Page 123 and 124: ase ply surface and up the primed w
Page 125 and 126: C. Lead Pipe Flashings: Completely
Page 127 and 128: Roofing Specification For: Citrus C
Page 129 and 130: Library - Lower Roof Area Project T
Page 131 and 132: 6. All penetrations into ducts shal
Page 133 and 134: All submittals which do not conform
Page 135 and 136: designated crew member shall watch
Page 137: Paradiene 20 TG P, by Siplast; Irvi
Page 141 and 142: Fabricate metal edge/fascia in maxi
Page 143 and 144: ASTM A 792. Steel decks should be s
Page 145 and 146: een applied to the top of the cant,
Page 147 and 148: (1) foot in either direction from t
show all

Bid #01-1112 Library and Reprographics Roofing ... - Citrus College

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?