Bid #01-1112 Library and Reprographics Roofing ... - Citrus College
Bid #01-1112 Library and Reprographics Roofing ... - Citrus College
Bid #01-1112 Library and Reprographics Roofing ... - Citrus College
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Again using a roller, apply an even top coat of catalyzed resin at the minimum rate<br />
specified by the resin manufacturer immediately following embedment of the fleece,<br />
ensuring full saturation of the fleece. Ensure that the flashing resin is applied to extend<br />
beyond the fleece (maximum 0.25 inch (6 mm)). Remove the tape before the catalyzed<br />
resin sets. Make allowances for saturation of roller covers <strong>and</strong> application equipment.<br />
4. Should work be interrupted for more than 12 hours or the surface of the catalyzed resin<br />
becomes dirty or contaminated by the elements, wipe the surface to be lapped with new<br />
flashing resin using the specified cleaner/solvent. Allow the surface to dry for a<br />
minimum 20 minutes <strong>and</strong> a maximum 60 minutes before continuing work.<br />
B. Field Membrane Application<br />
1. Using the specified cleaner/solvent, wipe flashing membrane surfaces to be lapped with<br />
field membrane. Allow the surface to dry for a minimum 20 minutes before continuing<br />
work.<br />
2. Apply an even, generous base coat of field membrane resin using a roller at the<br />
minimum rate specified by the resin manufacturer to prepared surfaces. Work the fleece<br />
into the wet, catalyzed resin using a roller to fully embed the fleece in the resin <strong>and</strong><br />
remove trapped air. Lap fleece layers a minimum of 2 inch (5 cm) <strong>and</strong> apply an<br />
additional coat of catalyzed resin between layers of overlapping fleece. Again using a<br />
roller, apply an even top coat of catalyzed resin at the minimum rate specified by the<br />
resin manufacturer immediately following embedment of the fleece, ensuring full<br />
saturation of the fleece. Make allowances for saturation of roller covers <strong>and</strong> application<br />
equipment. Allow 2 hours cure time prior to exposing the membrane to foot traffic.<br />
3.08 WALKTREAD/SKID RESISTANT SURFACING FOR RESIN ROOF SURFACES<br />
A. Granule Anti-Skid Application: Utilize masking tape to outline the areas to receive the<br />
anti-skid system. Apply an additional top coat of the catalyzed roof resin at the minimum<br />
rate specified by the resin manufacturer; <strong>and</strong> broadcast granules before the resin sets.<br />
Remove tape before the resin sets. Apply a coat of resin over the granule surface if<br />
required by the roofing system manufacturer.<br />
3.09 RELATED COMPONENTS - INSTALLATION<br />
A. Edge Metal: Completely prime metal flanges <strong>and</strong> allow to dry prior to installation. Turn the<br />
base ply down 2 inches past the roof edge <strong>and</strong> over the nailer. After the base ply <strong>and</strong><br />
continuous cleat (if applicable) have been installed, set the flange in mastic <strong>and</strong> stagger nail<br />
every 3 inches on center. Strip-in the flange using the stripping-ply material, extending a<br />
minimum of 4 inches beyond the edge of the flange. Terminate the finish ply at the gravelstop<br />
rise of the edge metal. SEE ITEM: SEALANT, for finish of this detail.<br />
B. Metal Coping: Metal coping shall be fabricated with a minimum four (4) inch face on each<br />
side. The cap metal shall be of sufficient width to adequately cover the top of the parapet<br />
wall. The bottom edge of each fascia shall have a minimum one-half (1/2) inch drip edge,<br />
hemmed <strong>and</strong> formed at thirty (30) degrees <strong>and</strong> shall be fabricated for attachment to a<br />
continous cleat at each side of the parapet. Metal coping shall be fabricated in maximum<br />
ten (10) feet sections. Fabricate corner pieces of metal coping to extend a minimum of one<br />
M-13-135 page - 20 <strong>Citrus</strong> <strong>Library</strong> <strong>Roofing</strong> Specification