Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 2 10 Sidekick Pro ISO Installation & Operation Manual
CHAPTER 3 Overview Chapt er 3Installation The following steps must be completed to install a Sidekick Pro ISO injection system: 1. Select and plumb the point of injection. See page 12. a. Install carrier and chemical injection check valves. b. Install in-line mixer. 2. Mount the Sidekick Pro ISO injection module or tank. See page 17. 3. Mount the Sidekick Pro ISO injection pump. See page 17. 4. Plumb the Sidekick Pro ISO pump and injection lines into the main carrier line at point of injection. See page 19. 5. Install the closed calibration system. See page 20. 6. Plumb the recommended rinse system. See page 21. 7. Connect the Sidekick Pro ISO injection pump to CANbus. See page 23. 8. Connect the Sidekick Pro ISO pump to source of electrical power. See page 23. The following sections provide detailed information and procedure to assist with completing the above steps. Contact a local Raven dealer for assistance or questions during the installation procedure. FIGURE 1. Example Sidekick Pro ISO Injection System Manual No. 016-0171-509 Rev. B 11
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13: Updates Introduction Updates for Ra
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66:
FIGURE 1. Check Valve Assemblies Di
Page 67 and 68:
FIGURE 2. Pump Head and Motor Separ
Page 69 and 70:
a. kerosene or fuel oil if the last
Page 71 and 72:
CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74:
Injection Pump Vacuum Switch To rep
Page 75 and 76:
FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78:
Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80:
FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82:
Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84:
FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86:
FIGURE 11. Injection Module (P/N 06
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?