Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 3 FIGURE 7. Sidekick Pro ISO Pump Mounting and Bracket Orientation Pump Mounting Bracket Pump Outlet Note: The pump mounting bracket may be rotated to accommodate mounting to a vertical surface, however, the injection pump must be mounted level with the outlet port perpendicular to the ground. 18 Sidekick Pro ISO Installation & Operation Manual Pump Inlet
FIGURE 8. Sidekick Pro ISO Pump Mounting Bracket Bolt Pattern Sidekick Pro ISO Injection System Plumbing Plumb the Sidekick Pro ISO Pump Pump Inlet Installation Use 3/4” chemically resistant hose between the chemical tank and injection pump inlet. Do not use hose or tubing that may collapse when a vacuum is applied during pump operation. The product line should be as straight as possible. Avoid low spots in plumbing to ease pump priming and avoid chemical waist. Strainer A strainer with a #20 mesh screen must be installed on the inlet side of the injection pump. Manual No. 016-0171-509 Rev. B 19 3
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15 and 16: CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21: Mount the Chemical Tank Installatio
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68: FIGURE 2. Pump Head and Motor Separ
Page 69 and 70: a. kerosene or fuel oil if the last
Page 71 and 72: CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74:
Injection Pump Vacuum Switch To rep
Page 75 and 76:
FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78:
Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80:
FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82:
Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84:
FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86:
FIGURE 11. Injection Module (P/N 06
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?