Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 8 FIGURE 5. Pump Encoder Midpoint Mark Set Screw 4. With the slide lock mechanism extended, align hub with motor shaft and firmly press down on hub to ensure the encoder is resting on the mounting surface. Do not press on encoder body, press on the hub only. 5. Hold the encoder assembly in place lightly to ensure the encoder remains in position. Encoder Hub Slide Lock Mechanism 6. Using the supplied wrench, tighten the hub set screw. Tighten the set screw by rotating approximately 60° with the supplied wrench. Do not overtighten the set screw to prevent damaging the motor shaft. If the hub set screw is overtightened, it may be difficult to remove the encoder in the future. 7. Rotate the body of the encoder if necessary to install the mounting screws in the center of each slot on the side of the encoder. 8. Install the mounting screws finger tight and press the slide lock mechanism toward the encoder body. • Insert the 8-pin connector on the encoder cable to the encoder body with the flat side toward the motor. Cable should lock in place. 72 Sidekick Pro ISO Installation & Operation Manual
Check Valve Assemblies FIGURE 6. Check Valve Spring Retainer Assemblies Replacement Parts Item Description Raven P/N Item Description Raven P/N 1 Fitting, Plug 107-0171-519 or 107-0171-955 a 1 Fitting, Plug 107-0171-519 2 O-Ring 219-0002-912 2 O-Ring 219-0002-912 3 Guide, Poppet 107-0159-934 3 Retainer, Intake 107-0171-459 4 Spring 314-0000-006 4 Spring 314-0000-005 5 Poppet 107-0159-935 5 Guide, Poppet 107-0171-092 6 O-Ring (Viton) 219-0007-011 b 6 Stem, Poppet 107-0171-447 7 Clip, Retainer 107-0171-576 7 O-Ring (Viton) 219-0007-011 b 8 Valve Body, Discharge 106-0159-621 8 Clip, Retainer 107-0171-576 9 O-Ring (Viton) 219-0002-018b 9 Valve, Body Intake 106-0159-622 a. Plug fitting (P/N 107-0171-955) is used with check valve assemblies (P/N 063-0173-310). b. O-Rings included in Pump Seal Kit (P/N 117-0159-987) Discharge Valve Assembly (P/N 063-0172-504 and 063-0173-310) 10 O-Ring (Viton) 219-0002-018 b Intake Valve Assembly (P/N 063-0172-503) 1. Press Down 2. Rotate 90° 3. Lift Up Manual No. 016-0171-509 Rev. B 73 8
Page 1 and 2:
Installation & Operation Manual Sid
Page 3 and 4:
Table of Contents Chapter 1 Importa
Page 5 and 6:
CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8:
CHAPTER 2 System Overview Chapt er
Page 9 and 10:
Fast Rate Response Introduction Hig
Page 11 and 12:
FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14:
Updates Introduction Updates for Ra
Page 15 and 16:
CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18:
FIGURE 3. Point of Injection Detail
Page 19 and 20:
TABLE 2. In-line Mixer Sizing and S
Page 21 and 22:
Mount the Chemical Tank Installatio
Page 23 and 24:
FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68: FIGURE 2. Pump Head and Motor Separ
Page 69 and 70: a. kerosene or fuel oil if the last
Page 71 and 72: CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74: Injection Pump Vacuum Switch To rep
Page 75: FIGURE 4. Gauge Tool and Flow Senso
Page 79 and 80: FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82: Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84: FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86: FIGURE 11. Injection Module (P/N 06
Page 93 and 94: A Application Modes 45 C Calibratio
Page 95 and 96: How Long is the Coverage Period? Ra
Page 98: Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?