Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 4 40 Sidekick Pro ISO Installation & Operation Manual
CHAPTER 5 Chapt er 5Operation Sidekick Pro ISO Priming and Calibration Before starting application of injected products, perform the following procedures to ensure the system is properly calibrated and ready for chemical application: 1. Verify control console setup 2. Prime the injection pump 3. Calibrate the injection pump Verify Control Console Settings Review the Virtual Terminal Calibration section on page 31 and verify that the correct settings for the chemical injection product are programmed for the correct product node or product number. Prime the Injection Pump 1. Open the hand valve(s) between the supply tank and injection pump. 2. Set the hand valve on the injection pump outlet to recirculate product back to the supply tank. 3. Lift the plunger handle on the pump calibrator to the top of the calibration cylinder. 4. Verify the following conditions are present: a. Vacuum pressure for the injected product must be less than 5.5 PSI [37.92 kPa] b. Injection pump discharge pressure must be less than 12 PSI [82.7 kPa] c. Injection product pump mode must be set to “CAL/PRM” (Calibration/Prime) d. Injection pump product master switch must be set to on Manual No. 016-0171-509 Rev. B 41
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15 and 16: CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43: Low Limit Calibration The low limit
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68: FIGURE 2. Pump Head and Motor Separ
Page 69 and 70: a. kerosene or fuel oil if the last
Page 71 and 72: CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74: Injection Pump Vacuum Switch To rep
Page 75 and 76: FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78: Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80: FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82: Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84: FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86: FIGURE 11. Injection Module (P/N 06
Page 93 and 94: A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

Create successful ePaper yourself

Delete template?

Save as template?