Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 4 1. Select the Tools icon from the soft keys area on the right side of the Product Control Home screen. 2. Touch the Alarms icon along the top of the display to access the Alarms Setup screen. Refer to the following sections for details on the alarm settings available on the Alarms Setup screen. Low Tank Enter the volume at which the system will display an alert when the calculated volume of product remaining in the tank drops below the desired value. Enter a value of zero to disable the low tank alarm. Off Rate Enter the percent at which the off rate alarm will activate. The off rate alarm activates when the actual rate differs from the target rate by the programmed value for longer than five seconds. FER Cal The FER (Flow Encoder Ratio) cal value is used to set the flow error tolerance of chemical injection applications. Increase the FER error cal value to set a tighter tolerance. Set the FER error cal to zero to turn off all flow monitor alarms for the injected chemical. The default value is 8. 38 Sidekick Pro ISO Installation & Operation Manual
Low Limit Calibration The low limit value sets the minimum volume per minute which a product will be applied. If the flow meter drops below this setting, an alert will be displayed on the VT control console. Note: The injection pump will maintain the current rate when the Low Limit setting is reached. Manual No. 016-0171-509 Rev. B 39 4
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15 and 16: CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41: Display Smoothing Calibration Toggl
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68: FIGURE 2. Pump Head and Motor Separ
Page 69 and 70: a. kerosene or fuel oil if the last
Page 71 and 72: CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74: Injection Pump Vacuum Switch To rep
Page 75 and 76: FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78: Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80: FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82: Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84: FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86: FIGURE 11. Injection Module (P/N 06
Page 93 and 94:
A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

Create successful ePaper yourself

Delete template?

Save as template?