Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 6 Software Part Number. The Raven part number of the software installed on the Sidekick Pro ISO system. Software Hours. Software revision level of the Sidekick Pro ISO node. Boot Loader Version. Revision level of the software boot loader on the Sidekick Pro ISO system. Task Controller Status. Indicates whether the Sidekick Pro ISO node is communicating with the ISOBUS task controller. Set Pump Number. Selected address for the Sidekick Pro ISO pump. 54 Sidekick Pro ISO Installation & Operation Manual
Injection Diagnostics and Troubleshooting Motor Control Node LED Status Indicators The Sidekick Pro ISO integrated motor control node displays the status of the injection pump with the following node status indicators. FIGURE 1. LED Status Indicators TABLE 1. LED Status Indicators Logic Power High Current Power Alarms LED Status Display TABLE 2. Sidekick Pro ISO Error Codes If logic power is present at the motor control node, the logic power indicator will be on. If high current power is present at the motor control node, the high current power indicator will be on. The CAN status indicator will flash once per second if the motor control node is CAN Status communicating on the CANbus. If the motor control node cannot communicate via the CANbus, the CAN status indicator will flash four times per second. Flow Switch State The flow switch indicator will flash once per revolution of the injection pump shaft. Calibration Switch State The calibration switch indicator will flash when a metal object is passed by the calibration switch sensor. Error Description Possible Cause Solution Off Rate Alarm Low Tank Alarm • Difference between actual and target application rates has been greater than 28% for more than 5 seconds • Chemical supply tank is below the refill threshold level Calibration Switch Logic Power High Current Power CAN Status Flow Switch State Cal Switch State • Required flow rate is out of range for the injection pump. Calculate the volume per minute required for the application and verify rate is within range of the injection pump. • Refill injection chemical supply tank and reset tank level in VT display. Manual No. 016-0171-509 Rev. B 55 6
Page 1 and 2:
Installation & Operation Manual Sid
Page 3 and 4:
Table of Contents Chapter 1 Importa
Page 5 and 6:
CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15 and 16: CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68: FIGURE 2. Pump Head and Motor Separ
Page 69 and 70: a. kerosene or fuel oil if the last
Page 71 and 72: CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74: Injection Pump Vacuum Switch To rep
Page 75 and 76: FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78: Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80: FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82: Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84: FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86: FIGURE 11. Injection Module (P/N 06
Page 93 and 94: A Application Modes 45 C Calibratio
Page 95 and 96: How Long is the Coverage Period? Ra
Page 98: Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?