Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 3 Initial Plumbing and Point of Injection The Raven Sidekick Pro ISO injection system pumps chemical into the main carrier line at the point of injection. This point must be on the pressure side of the carrier product pump and should be as close to the boom section valves as possible. Note: It is not necessary for injected products or chemicals to be measured by the flow meter. Depending upon the type of applications or chemical mixtures the injection system will normally be used with, it may be more desirable to place the injection point after the flow meter. This configuration will minimize the exposure of the flow meter to corrosive chemicals and may extend the life of the flow meter. FIGURE 2. Basic Sprayer Plumbing Diagram with Added Injection System 12 Sidekick Pro ISO Installation & Operation Manual
FIGURE 3. Point of Injection Detail From carrier product tank Installation Check valves are used in both the carrier and injection lines to prevent back flow and contamination of carrier and chemical reservoirs. An in-line mixer should be installed after the point of injection to ensure even mixing of the injected product. Once a point of injection has been selected: From injection module To boom valve manifold 1. Install a carrier check valve in the main product line to prevent back flow to the carrier reservoir. Use Table 1, “Check Valve Sizing and Selection Chart,” on page 14 to determine proper sizing of the carrier check valve. 2. Install a tee type fitting suitable for chemical applications after the carrier check valve. 3. Install an in-line mixer to the through port of the tee fitting and connect to the existing carrier product line or boom valve manifold. Use Table 2, “In-line Mixer Sizing and Selection Chart,” on page 15 to determine proper sizing of the in-line mixer. 4. Install a chemical injection check valve to the injection line in front of the point of injection to prevent back flow to the chemical reservoir. Use Table 1, “Check Valve Sizing and Selection Chart,” on page 14 to determine proper sizing of the carrier check valve. Manual No. 016-0171-509 Rev. B 13 3
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7 and 8: CHAPTER 2 System Overview Chapt er
Page 9 and 10: Fast Rate Response Introduction Hig
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15: CHAPTER 3 Overview Chapt er 3Instal
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60: Injection Diagnostics and Troublesh
Page 61 and 62: Error Description Possible Cause So
Page 63 and 64: CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66: FIGURE 1. Check Valve Assemblies Di
Page 67 and 68:
FIGURE 2. Pump Head and Motor Separ
Page 69 and 70:
a. kerosene or fuel oil if the last
Page 71 and 72:
CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74:
Injection Pump Vacuum Switch To rep
Page 75 and 76:
FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78:
Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80:
FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82:
Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84:
FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86:
FIGURE 11. Injection Module (P/N 06
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?