Installation & Operation Manual - StellarSupport - John Deere

More documents

Recommendations

Info

Chapter 2 Sidekick Pro ISO Features Closed Calibration System Calibrating chemical injection pumps is necessary for accurate chemical injection applications. The Sidekick Pro ISO closed calibration system allows the operator to perform calibration or system tests without catching or handling dangerous chemicals. Priming An automatic priming feature ensures the pump is correctly primed and ready for operation when the operator is ready to apply product. Pump Calibrator The pump calibrator provides a quick tool to check pump efficiency and verify that the pump is ready for operation. FIGURE 1. Pump Calibrator 4 Sidekick Pro ISO Installation & Operation Manual
Fast Rate Response Introduction High precision sensing allows the Sidekick Pro ISO direct injection pump to dynamically lock onto the target rate while the application equipment works the field. This ensures that the injection pump is providing the proper chemical concentration throughout the field regardless of vehicle speed or boom section status changes. Integrated Motor Control Node Sidekick Pro ISO features an integrated motor control node mounted directly on the pump housing for simplified installation and enhanced performance. The control node features status LEDs which provide status and CAN communication information which the operator may be able to use during calibration or system troubleshooting. Integrated Calibration Switch The integrated motor control node also features a sealed calibration switch. The sealed calibration switch allows the operator to begin the pump calibration process by passing a metallic object, such as a screwdriver, across the switch sensor on the Sidekick Pro ISO injection pump. This feature allows the operator to run multiple calibration tests quickly and easily and ensure the system is ready for operation. Note: Calibration must be initiated from the control console in the vehicle cab. See the Calibrate the Injection Pump section on page 43 for a detailed calibration procedure. The calibration status LED light will flash when the calibration sensor registers a metallic object by the switch. Pass the metal object past the sensor to initiate a pump calibration. FIGURE 2. Motor Control Node Calibration Sensor Calibration Status LED Calibration Sensor Location Manual No. 016-0171-509 Rev. B 5 2
Page 1 and 2: Installation & Operation Manual Sid
Page 3 and 4: Table of Contents Chapter 1 Importa
Page 5 and 6: CHAPTER 1 Chapt er 1Important Safet
Page 7: CHAPTER 2 System Overview Chapt er
Page 11 and 12: FIGURE 3. Sidekick Pro ISO Injectio
Page 13 and 14: Updates Introduction Updates for Ra
Page 15 and 16: CHAPTER 3 Overview Chapt er 3Instal
Page 17 and 18: FIGURE 3. Point of Injection Detail
Page 19 and 20: TABLE 2. In-line Mixer Sizing and S
Page 21 and 22: Mount the Chemical Tank Installatio
Page 23 and 24: FIGURE 8. Sidekick Pro ISO Pump Mou
Page 25 and 26: Recirculation Check Valve Installat
Page 27 and 28: ISOBUS and Power Connections Instal
Page 29 and 30: Installation FIGURE 11. Sidekick Pr
Page 31 and 32: Verify Installation of the Sidekick
Page 33 and 34: CHAPTER 4 Chapt er 4Calibration Det
Page 35 and 36: Virtual Terminal Calibration Calibr
Page 37 and 38: Rate Cal (Target) The programmed ta
Page 39 and 40: FIGURE 1. Sidekick Pro ISO Pump Mot
Page 41 and 42: Display Smoothing Calibration Toggl
Page 43 and 44: Low Limit Calibration The low limit
Page 45 and 46: CHAPTER 5 Chapt er 5Operation Sidek
Page 47 and 48: Calibrate the Injection Pump Operat
Page 49 and 50: Application Modes and Pump Operatio
Page 51 and 52: Operation The Product Control Home
Page 53 and 54: 4. Select the Product Totals icon f
Page 55 and 56: CHAPTER 6 Product Diagnostics Scree
Page 57 and 58: Injection Diagnostics and Troublesh
Page 59 and 60:
Injection Diagnostics and Troublesh
Page 61 and 62:
Error Description Possible Cause So
Page 63 and 64:
CHAPTER 7 Chapt er 7System Maintena
Page 65 and 66:
FIGURE 1. Check Valve Assemblies Di
Page 67 and 68:
FIGURE 2. Pump Head and Motor Separ
Page 69 and 70:
a. kerosene or fuel oil if the last
Page 71 and 72:
CHAPTER 8 Chapt er 8Replacement Par
Page 73 and 74:
Injection Pump Vacuum Switch To rep
Page 75 and 76:
FIGURE 4. Gauge Tool and Flow Senso
Page 77 and 78:
Check Valve Assemblies FIGURE 6. Ch
Page 79 and 80:
FIGURE 7. Sidekick Pro ISO Pump (P/
Page 81 and 82:
Sidekick Pro ISO 5 to 200 oz./min.
Page 83 and 84:
FIGURE 10. Sidekick Pro ISO Pump (P
Page 85 and 86:
FIGURE 11. Injection Module (P/N 06
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
A Application Modes 45 C Calibratio
Page 95 and 96:
How Long is the Coverage Period? Ra
Page 98:
Sidekick Pro ISO 1 to 40 oz./min an
show all

Installation & Operation Manual - StellarSupport - John Deere

Create successful ePaper yourself

Delete template?

Save as template?