TELE-TECH & - AmericanRadioHistory.Com

pOCKETSCOpESk
PANELSCOPES`''
kSeOP
PULSESCOPES S° 0°1%
SYSTEMS CONCEPT
RAKSCOPE S-12-C
PANELSCOPE
The Waterman SYSTEMS RAKSCOPE, S -12 -C series is a rack mounted
oscilloscope with SYSTEMS CONCEPT. Systems concept is a basic means
for rapid monitoring of desired signals with minimum operative effort and
without the use of auxiliary switching or jack panels. S -12 -C series provide
the following:
1. BASIC UNIT -The basic S -12 -C SYSTEMS RAKSCOPE is a complete combination
systems monitoring and trouble- shooting oscilloscope with outstanding
physical and electrical characteristics. The RAKSCOPE occupies but 7
inches of a standard 19" rack and extends only 10 inches behind the front
panel. Identical vertical and horizontal amplifiers are DC type having rise
times better than 0.35 usec, and 50 or 71 millivolts rms per inch of deflection
respectively. Signal calibration method uses a direct reading accurate meter.
Time base sweeps are from'/ cps to 50KC in trigger or repetitive operation.
Sync from internal or external sources provide stable operation by means of
new sync lockout circuits. Special plug -in elliptical sweep circuit for easy
phase and frequency checks greatly increase its systems utility. Construction
is ruggedized throughout. Tube type options include standard commercial,
ruggedized commercial or ruggedized military. Operable from 50 to 400 cycles.
2. CUSTOM MODIFICATION- Desired flexibility is obtained with the
optional signal input selector. For the first time it is possible to select up to
eleven different signal sources with the necessary built -in attenuation
(supplied by us or by you) for each source. Thus the entire switching panel
can be omitted from an overall system resulting in circuit and space economics.
Standard elliptical sweep is 60 cycles, but plug -in units for other frequencies
can be supplied. Accessories such as attenuating, direct, and amplifying
probes are available.
Improve your existing or contemplated systems by including the S -I2 -C
SYSTEMS RAKSCOPE as an integral part. Your local Waterman representative
is ready to assist you in determining specific requirements.
RAYON!
C
CATHODE RAY TUBES
TheWaterman PANELSCOPE is a custom -built cathode ray tube oscilloscope,
with simplified operation, and yet available at a low price. The PANELSCOPE
concept provides for the following:
(1) MINIATURIZATION -Panel space required is only 51/4" x 5.3/16" -
depth is 10" and the weight is less than 7 lbs. The PANELSCOPE can be
installed in practically any equipment -mobile or stationary -air, sea, or
land- military or commercial.
(2) SIMPLICITY OF OPERATION -Twist of a single rotary switch provides a
synchronized pattern of desired incoming signal (up to 11 circuits) against
proper linear time base. This is ideal for monitoring and trouble shooting,
as it removes the need of fiddling with knobs as is done now on general
purpose oscilloscopes. The static controls, such as beam, focus, positioning,
and graticule brightness are located in tube escutcheon.
(3) CUSTOM DESIGN -A wide variety of- signal amplifiers with response
from dc to megacycles and sensitivities from 5 millivolts- synchronized or
triggered linear time base generators from % cycle (and lower if need be)
to 2 microseconds -can be specified by you to fit your needs for particular
equipment.
(4) PARTIAL KIT FORM -the PANELSCOPE comes fully wired and tested
with chosen signal amplifier, linear time base generator and attendant sync.
amplifier. The desired signal attenuators, frequency and amplitude determining
components, and method of synchronization can be installed either by us
or by you.
(5) POWER REQUIREMENT -Less than 10 watts of line power for built -in
high voltage supply -The required B+ and heater current as selected by
your requirements. For those cases where B+ and heater power is not
available, auxiliary power pack can be supplied.
There is a place in your equipment for Waterman PANELSCOPE, a custom
built oscilloscope at production prices, although your needs may be but one
or two. Ask for specification sheets either from our representatives or direct
from the factory.
Y
WATERMAN
TUBE
PHYSICAL DATA STATIC VOLTAGE DEFLECTION. LIGHT
OUTPUT
FACE LENGTH A3 A2 VERT HOR
301 3" 10" 3000 1500 III 150 40
3MPI 3" 8" 750 99 104 4
3RP1 3" 9.12" 1000 61 86 5
3581 1.5E3" 9.12" 1000 61 86 5
3XP1 1.50" 8.875" 2000 33 80 22
The basic properties of the cathode ray tube that concern the designer or the
user are: deflection sensitivity, unit line brightness, line width, static voltage
requirements and physical size. A comparison between cathode ray tubes
manufactured by Waterman Products Company is shown in the table adjoining.
These tubes are available in P1, P2, P7 and Pll phosphors. 3JP1.
3JP2, 3JP7, 3RPI, 3SP1 and 3XP1 are available as JAN tubes.
*Deflection in volts per inch.
ieliph output of o line in milliroof lamberts per millimeter of line width not fo exceed .65mm.
WATERMAN PRO
PHILADELPHIA 25, PENNA., U.S.A.
DUCTS CO., INC.
CABLE ADDRESS, POKETSCOPE, PHILA.
WATERMAN PRODUCTS
Manufacturers of Pocketscopes Rakscopes Pulsescope Panelscopes' and Rayonic Tubes
Tele -Tech & ELECTRONIC INDUSTRIES June 1956 For product information, use inquiry card on pages 209.215. 67