- Page 1:
78-4021716-01 Rev C Prisma II 1310
- Page 4 and 5:
Notices Trademark Acknowledgments C
- Page 6 and 7:
Contents Connecting the RF Cables t
- Page 8 and 9:
Contents To Change Parameters .....
- Page 11 and 12:
Important Safety Instructions Impor
- Page 13 and 14:
Important Safety Instructions Rout
- Page 15 and 16:
Important Safety Instructions Note:
- Page 17 and 18:
Important Safety Instructions warni
- Page 19:
Important Safety Instructions Other
- Page 22 and 23:
Laser Safety Safe Operation for Sof
- Page 24 and 25:
Laser Power and Warning Labels Loca
- Page 26 and 27:
Qualified Personnel Only appropriat
- Page 28 and 29:
Chapter 1 Module Introduction In M
- Page 30 and 31:
Chapter 1 Module Introduction Back
- Page 32 and 33:
Chapter 1 Module Introduction Side
- Page 34 and 35:
Chapter 1 Module Introduction Confi
- Page 36 and 37:
Chapter 2 Module Installation Prepa
- Page 38 and 39:
Chapter 2 Module Installation Space
- Page 40 and 41:
Chapter 2 Module Installation Prism
- Page 42 and 43:
Chapter 2 Module Installation Prism
- Page 44 and 45:
Chapter 2 Module Installation To In
- Page 46 and 47:
Chapter 2 Module Installation 2 Ali
- Page 48 and 49:
Chapter 2 Module Installation Optic
- Page 50 and 51:
Chapter 2 Module Installation To Co
- Page 52 and 53:
Chapter 2 Module Installation To Co
- Page 54 and 55:
Chapter 2 Module Installation Using
- Page 56 and 57:
Chapter 2 Module Installation For d
- Page 59 and 60:
3 Chapter 3 Operation using ICIM In
- Page 61 and 62:
ICIM Introduction ICIM Introduction
- Page 63 and 64:
ICIM2 Front Panel ICIM2 Front Panel
- Page 65 and 66: ICIM Keypad ICIM2 Front Panel The I
- Page 67 and 68: ICIM Password 2 Use the 3 Press the
- Page 69 and 70: ICIM Password 5 Press the ENTER key
- Page 71 and 72: Operating the ICIM Operating the IC
- Page 73 and 74: Operating the ICIM ICIM Shelf 0 Slo
- Page 75 and 76: Checking the Operating Status using
- Page 77 and 78: Configuring the Module using the IC
- Page 79 and 80: Checking Module Alarms using the IC
- Page 81 and 82: Checking Module Alarms using the IC
- Page 83 and 84: Checking Manufacturing Data using t
- Page 85 and 86: SNMP Configuration SNMP Configurati
- Page 87 and 88: SNMP Configuration To Restart the I
- Page 89 and 90: Setting SNMP Trap Receiver Paramete
- Page 91 and 92: New SNMP Variables Variable p2Remov
- Page 93 and 94: Boot Dialog for ICIM/SNMP Configura
- Page 95: Adjusting Alarm Thresholds Adjustin
- Page 98 and 99: Chapter 4 Operation using LCI LCI I
- Page 100 and 101: Chapter 4 Operation using LCI Insta
- Page 102 and 103: Chapter 4 Operation using LCI 5 Whe
- Page 104 and 105: Chapter 4 Operation using LCI Prism
- Page 106 and 107: Chapter 4 Operation using LCI Resul
- Page 108 and 109: Chapter 4 Operation using LCI Acces
- Page 110 and 111: Chapter 4 Operation using LCI To Ac
- Page 112 and 113: Chapter 4 Operation using LCI Resul
- Page 114 and 115: Chapter 4 Operation using LCI Confi
- Page 118 and 119: Chapter 4 Operation using LCI Modif
- Page 120 and 121: Chapter 4 Operation using LCI Check
- Page 122 and 123: Chapter 5 Maintenance and Troublesh
- Page 124 and 125: Chapter 5 Maintenance and Troublesh
- Page 127 and 128: A Appx auto letter Module Parameter
- Page 129 and 130: High Density Transmitter Parameters
- Page 131: High Density Transmitter Parameters
- Page 134 and 135: H I L M Glossary fields. EMT extern
- Page 136 and 137: T Glossary SMC status monitoring an
- Page 138 and 139: Index High Density Transmitter Feat
- Page 140: Cisco Systems, Inc. 5030 Sugarloaf