- Page 1: 78-4021716-01 Rev C Prisma II 1310
- Page 4 and 5: Notices Trademark Acknowledgments C
- Page 6 and 7: Contents Connecting the RF Cables t
- Page 8 and 9: Contents To Change Parameters .....
- Page 11 and 12: Important Safety Instructions Impor
- Page 13 and 14: Important Safety Instructions Rout
- Page 15 and 16: Important Safety Instructions Note:
- Page 17 and 18: Important Safety Instructions warni
- Page 19: Important Safety Instructions Other
- Page 24 and 25: Laser Power and Warning Labels Loca
- Page 26 and 27: Qualified Personnel Only appropriat
- Page 28 and 29: Chapter 1 Module Introduction In M
- Page 30 and 31: Chapter 1 Module Introduction Back
- Page 32 and 33: Chapter 1 Module Introduction Side
- Page 34 and 35: Chapter 1 Module Introduction Confi
- Page 36 and 37: Chapter 2 Module Installation Prepa
- Page 38 and 39: Chapter 2 Module Installation Space
- Page 40 and 41: Chapter 2 Module Installation Prism
- Page 42 and 43: Chapter 2 Module Installation Prism
- Page 44 and 45: Chapter 2 Module Installation To In
- Page 46 and 47: Chapter 2 Module Installation 2 Ali
- Page 48 and 49: Chapter 2 Module Installation Optic
- Page 50 and 51: Chapter 2 Module Installation To Co
- Page 52 and 53: Chapter 2 Module Installation To Co
- Page 54 and 55: Chapter 2 Module Installation Using
- Page 56 and 57: Chapter 2 Module Installation For d
- Page 59 and 60: 3 Chapter 3 Operation using ICIM In
- Page 61 and 62: ICIM Introduction ICIM Introduction
- Page 63 and 64: ICIM2 Front Panel ICIM2 Front Panel
- Page 65 and 66: ICIM Keypad ICIM2 Front Panel The I
- Page 67 and 68: ICIM Password 2 Use the 3 Press the
- Page 69 and 70: ICIM Password 5 Press the ENTER key
- Page 71 and 72: Operating the ICIM Operating the IC
- Page 73 and 74:
Operating the ICIM ICIM Shelf 0 Slo
- Page 75 and 76:
Checking the Operating Status using
- Page 77 and 78:
Configuring the Module using the IC
- Page 79 and 80:
Checking Module Alarms using the IC
- Page 81 and 82:
Checking Module Alarms using the IC
- Page 83 and 84:
Checking Manufacturing Data using t
- Page 85 and 86:
SNMP Configuration SNMP Configurati
- Page 87 and 88:
SNMP Configuration To Restart the I
- Page 89 and 90:
Setting SNMP Trap Receiver Paramete
- Page 91 and 92:
New SNMP Variables Variable p2Remov
- Page 93 and 94:
Boot Dialog for ICIM/SNMP Configura
- Page 95:
Adjusting Alarm Thresholds Adjustin
- Page 98 and 99:
Chapter 4 Operation using LCI LCI I
- Page 100 and 101:
Chapter 4 Operation using LCI Insta
- Page 102 and 103:
Chapter 4 Operation using LCI 5 Whe
- Page 104 and 105:
Chapter 4 Operation using LCI Prism
- Page 106 and 107:
Chapter 4 Operation using LCI Resul
- Page 108 and 109:
Chapter 4 Operation using LCI Acces
- Page 110 and 111:
Chapter 4 Operation using LCI To Ac
- Page 112 and 113:
Chapter 4 Operation using LCI Resul
- Page 114 and 115:
Chapter 4 Operation using LCI Confi
- Page 116 and 117:
Chapter 4 Operation using LCI Check
- Page 118 and 119:
Chapter 4 Operation using LCI Modif
- Page 120 and 121:
Chapter 4 Operation using LCI Check
- Page 122 and 123:
Chapter 5 Maintenance and Troublesh
- Page 124 and 125:
Chapter 5 Maintenance and Troublesh
- Page 127 and 128:
A Appx auto letter Module Parameter
- Page 129 and 130:
High Density Transmitter Parameters
- Page 131:
High Density Transmitter Parameters
- Page 134 and 135:
H I L M Glossary fields. EMT extern
- Page 136 and 137:
T Glossary SMC status monitoring an
- Page 138 and 139:
Index High Density Transmitter Feat
- Page 140:
Cisco Systems, Inc. 5030 Sugarloaf