Prisma II 1310 nm High Density Transmitter and Host Module ...

More documents

Recommendations

Info

Chapter 5 Maintenance and Troubleshooting Maintenance The following maintenance is recommended to ensure optimal performance. Frequency Yearly When needed Maintenance Required • Check all parameters and test points. • Record data. • Make adjustments as needed. • Make sure all cables are mated properly. • Inspect cables for stress and chafing. • Make sure all retaining screws are tight. • Replace chassis air filter. Depending on office environment cleanliness/filtration, the chassis air filter may require more frequent servicing. Carefully clean the module with a soft cloth that is dampened with mild detergent. Maintenance Record It may be helpful to establish a maintenance record or log for this equipment. You may want to record laser power level, laser temperature readings, laser bias current, or power supply voltages, as well as the filter change dates. Large variations in any of the parameters above should be investigated prior to failure. 98 78-4021716-01 Rev C
General Troubleshooting Information General Troubleshooting Information This troubleshooting information describes the most common alarms and gives typical symptoms, causes, and items to check before contacting Cisco Services. Equipment Needed You may need the following equipment to troubleshoot these modules. Digital voltmeter Fiber connector cleaning materials Additional Assistance Troubleshooting If you need additional assistance contact Cisco Services. Refer to Troubleshooting Alarm Conditions (on page 100) to identify and correct faults. WARNING: Avoid electric shock and damage to this product! Do not open the enclosure of this product. There are no user-serviceable parts inside. Refer servicing to qualified and skilled personnel. 78-4021716-01 Rev C 99
Page 1:
78-4021716-01 Rev C Prisma II 1310
Page 4 and 5:
Notices Trademark Acknowledgments C
Page 6 and 7:
Contents Connecting the RF Cables t
Page 8 and 9:
Contents To Change Parameters .....
Page 11 and 12:
Important Safety Instructions Impor
Page 13 and 14:
Important Safety Instructions Rout
Page 15 and 16:
Important Safety Instructions Note:
Page 17 and 18:
Important Safety Instructions warni
Page 19:
Important Safety Instructions Other
Page 22 and 23:
Laser Safety Safe Operation for Sof
Page 24 and 25:
Laser Power and Warning Labels Loca
Page 26 and 27:
Qualified Personnel Only appropriat
Page 28 and 29:
Chapter 1 Module Introduction In M
Page 30 and 31:
Chapter 1 Module Introduction Back
Page 32 and 33:
Chapter 1 Module Introduction Side
Page 34 and 35:
Chapter 1 Module Introduction Confi
Page 36 and 37:
Chapter 2 Module Installation Prepa
Page 38 and 39:
Chapter 2 Module Installation Space
Page 40 and 41:
Chapter 2 Module Installation Prism
Page 42 and 43:
Chapter 2 Module Installation Prism
Page 44 and 45:
Chapter 2 Module Installation To In
Page 46 and 47:
Chapter 2 Module Installation 2 Ali
Page 48 and 49:
Chapter 2 Module Installation Optic
Page 50 and 51:
Chapter 2 Module Installation To Co
Page 52 and 53:
Chapter 2 Module Installation To Co
Page 54 and 55:
Chapter 2 Module Installation Using
Page 56 and 57:
Chapter 2 Module Installation For d
Page 59 and 60:
3 Chapter 3 Operation using ICIM In
Page 61 and 62:
ICIM Introduction ICIM Introduction
Page 63 and 64:
ICIM2 Front Panel ICIM2 Front Panel
Page 65 and 66:
ICIM Keypad ICIM2 Front Panel The I
Page 67 and 68:
ICIM Password 2 Use the 3 Press the
Page 69 and 70:
ICIM Password 5 Press the ENTER key
Page 71 and 72: Operating the ICIM Operating the IC
Page 73 and 74: Operating the ICIM ICIM Shelf 0 Slo
Page 75 and 76: Checking the Operating Status using
Page 77 and 78: Configuring the Module using the IC
Page 79 and 80: Checking Module Alarms using the IC
Page 81 and 82: Checking Module Alarms using the IC
Page 83 and 84: Checking Manufacturing Data using t
Page 85 and 86: SNMP Configuration SNMP Configurati
Page 87 and 88: SNMP Configuration To Restart the I
Page 89 and 90: Setting SNMP Trap Receiver Paramete
Page 91 and 92: New SNMP Variables Variable p2Remov
Page 93 and 94: Boot Dialog for ICIM/SNMP Configura
Page 95: Adjusting Alarm Thresholds Adjustin
Page 98 and 99: Chapter 4 Operation using LCI LCI I
Page 100 and 101: Chapter 4 Operation using LCI Insta
Page 102 and 103: Chapter 4 Operation using LCI 5 Whe
Page 104 and 105: Chapter 4 Operation using LCI Prism
Page 106 and 107: Chapter 4 Operation using LCI Resul
Page 108 and 109: Chapter 4 Operation using LCI Acces
Page 110 and 111: Chapter 4 Operation using LCI To Ac
Page 112 and 113: Chapter 4 Operation using LCI Resul
Page 114 and 115: Chapter 4 Operation using LCI Confi
Page 116 and 117: Chapter 4 Operation using LCI Check
Page 118 and 119: Chapter 4 Operation using LCI Modif
Page 120 and 121: Chapter 4 Operation using LCI Check
Page 124 and 125: Chapter 5 Maintenance and Troublesh
Page 127 and 128: A Appx auto letter Module Parameter
Page 129 and 130: High Density Transmitter Parameters
Page 131: High Density Transmitter Parameters
Page 134 and 135: H I L M Glossary fields. EMT extern
Page 136 and 137: T Glossary SMC status monitoring an
Page 138 and 139: Index High Density Transmitter Feat
Page 140: Cisco Systems, Inc. 5030 Sugarloaf
show all

Prisma II 1310 nm High Density Transmitter and Host Module ...

Create successful ePaper yourself

Delete template?

Save as template?