Prisma II 1310 nm High Density Transmitter and Host Module ...

More documents

Recommendations

Info

Chapter 2 Module Installation For detailed information on ALARM IN and ALARM OUT connectors, see the Prisma II Chassis Installation and Operation Guide, part number 713375 or the Prisma II XD Platform System Guide, part number 4021339. When a critical alarm occurs in a Master module, the Master turns off and the Slave (redundant module) is enabled. To make this happen, the pin representing the Master module slot in the ALARM OUT connector must be externally wired to the pin representing the Slave module slot in the ALARM IN connector. After wiring these contacts, take care to ensure that the Master and Slave modules are not moved to other slots. Otherwise, the ALARM IN and ALARM OUT connectors will need to be rewired to the appropriate pins. Note: Any device configured as Single or Master ignores its ALARM IN contacts. To verify proper wiring and redundant configuration, simply unplug the Master module and observe that the Slave module turns on. Master/Slave Illustration Redundancy Interface Panel The Prisma II Redundancy Interface Panel is an accessory to the Prisma II platform. It is intended to be used with the master/slave feature and the contact closure alarm feature of the Prisma II platform. The Prisma II Redundancy Interface Panel serves as an extension to the two DB-37 connectors labeled ALARM IN and ALARM OUT on the connector interface panel of the chassis. The terminals on the redundancy interface panel are extensions of pins on the ALARMS OUT and ALARMS IN connectors on the chassis. 32 78-4021716-01 Rev C
External Alarms Connections For additional information, see the Prisma II Chassis Installation and Operation Guide, part number 713375. Prisma II Redundancy Interface Panel Illustrations Front Panel Back Panel Close-up of Front Panel Terminal Strips 78-4021716-01 Rev C 33
Page 1:
78-4021716-01 Rev C Prisma II 1310
Page 4 and 5:
Notices Trademark Acknowledgments C
Page 6 and 7: Contents Connecting the RF Cables t
Page 8 and 9: Contents To Change Parameters .....
Page 11 and 12: Important Safety Instructions Impor
Page 13 and 14: Important Safety Instructions Rout
Page 15 and 16: Important Safety Instructions Note:
Page 17 and 18: Important Safety Instructions warni
Page 19: Important Safety Instructions Other
Page 22 and 23: Laser Safety Safe Operation for Sof
Page 24 and 25: Laser Power and Warning Labels Loca
Page 26 and 27: Qualified Personnel Only appropriat
Page 28 and 29: Chapter 1 Module Introduction In M
Page 30 and 31: Chapter 1 Module Introduction Back
Page 32 and 33: Chapter 1 Module Introduction Side
Page 34 and 35: Chapter 1 Module Introduction Confi
Page 36 and 37: Chapter 2 Module Installation Prepa
Page 38 and 39: Chapter 2 Module Installation Space
Page 40 and 41: Chapter 2 Module Installation Prism
Page 42 and 43: Chapter 2 Module Installation Prism
Page 44 and 45: Chapter 2 Module Installation To In
Page 46 and 47: Chapter 2 Module Installation 2 Ali
Page 48 and 49: Chapter 2 Module Installation Optic
Page 50 and 51: Chapter 2 Module Installation To Co
Page 52 and 53: Chapter 2 Module Installation To Co
Page 54 and 55: Chapter 2 Module Installation Using
Page 59 and 60: 3 Chapter 3 Operation using ICIM In
Page 61 and 62: ICIM Introduction ICIM Introduction
Page 63 and 64: ICIM2 Front Panel ICIM2 Front Panel
Page 65 and 66: ICIM Keypad ICIM2 Front Panel The I
Page 67 and 68: ICIM Password 2 Use the 3 Press the
Page 69 and 70: ICIM Password 5 Press the ENTER key
Page 71 and 72: Operating the ICIM Operating the IC
Page 73 and 74: Operating the ICIM ICIM Shelf 0 Slo
Page 75 and 76: Checking the Operating Status using
Page 77 and 78: Configuring the Module using the IC
Page 79 and 80: Checking Module Alarms using the IC
Page 81 and 82: Checking Module Alarms using the IC
Page 83 and 84: Checking Manufacturing Data using t
Page 85 and 86: SNMP Configuration SNMP Configurati
Page 87 and 88: SNMP Configuration To Restart the I
Page 89 and 90: Setting SNMP Trap Receiver Paramete
Page 91 and 92: New SNMP Variables Variable p2Remov
Page 93 and 94: Boot Dialog for ICIM/SNMP Configura
Page 95: Adjusting Alarm Thresholds Adjustin
Page 98 and 99: Chapter 4 Operation using LCI LCI I
Page 100 and 101: Chapter 4 Operation using LCI Insta
Page 102 and 103: Chapter 4 Operation using LCI 5 Whe
Page 104 and 105: Chapter 4 Operation using LCI Prism
Page 106 and 107:
Chapter 4 Operation using LCI Resul
Page 108 and 109:
Chapter 4 Operation using LCI Acces
Page 110 and 111:
Chapter 4 Operation using LCI To Ac
Page 112 and 113:
Chapter 4 Operation using LCI Resul
Page 114 and 115:
Chapter 4 Operation using LCI Confi
Page 116 and 117:
Chapter 4 Operation using LCI Check
Page 118 and 119:
Chapter 4 Operation using LCI Modif
Page 120 and 121:
Chapter 4 Operation using LCI Check
Page 122 and 123:
Chapter 5 Maintenance and Troublesh
Page 124 and 125:
Chapter 5 Maintenance and Troublesh
Page 127 and 128:
A Appx auto letter Module Parameter
Page 129 and 130:
High Density Transmitter Parameters
Page 131:
High Density Transmitter Parameters
Page 134 and 135:
H I L M Glossary fields. EMT extern
Page 136 and 137:
T Glossary SMC status monitoring an
Page 138 and 139:
Index High Density Transmitter Feat
Page 140:
Cisco Systems, Inc. 5030 Sugarloaf
show all

Prisma II 1310 nm High Density Transmitter and Host Module ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?