audio file in the INSERT mode - Fostex

More documents

Recommendations

Info

Reformatting a DVD-RAM disk The following describes how to reformat a used disk, while chapter 1 describes how to format a new disk. We assume that a used DVD-RAM disk is inserted in the tray and stopped. Before reformatting a used disk in the Tape mode, set the [AUDIO FILE], [SAMPLING FREQ] and [TR MODE] switches on the front panel appropriately, which determine the behavior of the newly created "Tape mode" file. Memory point data still remain after reformatting a disk. Therefore, if you do not need the old memory point data, delete them using the delete function. See "Chapter 6: Editing/storing time data" for details about how to delete memory point data. 1. While stopped, press the [SHIFT] key to turn on the indicator. 2. Press the [SETUP] key. The unit enters the Utility mode and the display shows a setting menu. The first time the unit enters the Utility mode after turning on the unit, the "Rec Protect?" menu is shown. Otherwise, the previously used setting menu is shown. Flashing 1 2 ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL BIT FS kHz -0.1% FORMAT BWF 48 24 3. Use the jog dial to select the "Format?" menu and press the [ENTER/YES] key. The display changes to show "Format Disk DVD". Flashing Flashing 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 4. Press the [ENTER/YES] key again. The display shows the following and now you can edit the volume name of the disk (which is tentatively named "DV40-DVD"). See the next "Tips" about how to edit a volume name, although you may go to the next step without editing the volume name. Flashing 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 CLOCK -INT- CLOCK -INT- CLOCK -INT- CLOCK -INT- 3-2
Tips: How to edit a volume name While the leftmost character of the tentative name is flashing, press the [MARGIN RESET/CLR] key repeatedly to delete the name. Then, enter the desired alphanumeric characters using the numeric keys or the jog dial. When using the numeric keys, the editing point (flashing point) moves by pressing any of the numeric keys after entering a character. When using the jog dial, you can move the editing point by using the [SKIP/CURSOR] ([||]) keys. 5. Press the [ENTER/YES] key again. The display changes to show "Format Md?" with flashing "Norm". You can select the format mode between "Norm" (Normal) and "Tape" using the jog dial. See "Formatting a DVD-RAM disk" in "Chapter 1 Before using the DV40" for details about the format mode. Flashing 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 CLOCK -INT- 6. Select the format mode and press the [ENTER/YES] key. Depending on the format mode selected, the display shows as follows. • When selecting "Norm": The display scrolls "If enter key is pushed, will start formatting and delete DVD area data. Are you sure?". • When selecting "Tape": The display shows "Disk Type?" with flashing "New" for selecting disk type. Select "Used" using the jog dial, and then go to the next step. Flashing 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 1 2 BIT FS kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% FORMAT BWF 48 24 CLOCK -INT- CLOCK -INT- When a used disk previously formatted in the Tape mode is reformatted in the Tape mode by selecting "New" for the disk type, the "Tape mode" file data is not erased (while "Normal mode" files are erased). Therefore, if you record a new material to the old "Tape mode" file, new and old materials may exist together. To erase all sound data when reformatting a disk in the Tape mode, make sure to select "Used" for the disk type. Tips: Special usage of "New" In general, "New" for the disk type is selected when formatting a new DVD-RAM disk. However, there is a special case. If you cannot playback a recorded "Tape mode" file for any reason, reformat the disk in the Tape mode by selecting "New" for the disk type. The "Tape mode" file data remains after reformatting and may be played back correctly. All the "Normal mode" files on the disk are erased. 3-3
Page 1 and 2: KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 3 and 4: Table of Contents Chapter-1 Before
Page 5 and 6: Chapter-9 Audio file management Cre
Page 7 and 8: Chapter-1 Before using the DV40 Bef
Page 9 and 10: Setting the internal clock The inte
Page 11 and 12: Formatting a DVD-RAM disk To make a
Page 13 and 14: About audio files on a formatted di
Page 15 and 16: Chapter-2 Names and Functions This
Page 17 and 18: Front panel part 1 3 4 5 6 7 DVD MA
Page 19 and 20: c. [PLAY] key Normally, pressing th
Page 21 and 22: DISP TIME 15. [DISP TIME] key Cycle
Page 23 and 24: CUE POINT IN DST OUT PREVIEW TR3 TR
Page 25 and 26: NEW FILE INPUT MON 40. [AUDIO RDY -
Page 27 and 28: 50. [TC GEN MODE] switch Selects th
Page 29 and 30: 4. ETHERNET port ETHERNET 10/100 LI
Page 31: Chapter 3 Reformatting/optimizing a
Page 35 and 36: Optimizing a disk By optimizing a u
Page 37 and 38: Chapter 4 Audio recording/playback
Page 39 and 40: Recording an analog source in the N
Page 41 and 42: Recording 1. Press the [RECORD] key
Page 43 and 44: You can create an audio file before
Page 45 and 46: Selecting a desired file on a disk
Page 47 and 48: Creating a "Normal mode" audio file
Page 49 and 50: KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 51 and 52: MUTE recording You can make mute re
Page 53 and 54: Cueing by the jog function You can
Page 55 and 56: Chapter 5 Timecode recording This c
Page 57 and 58: ABS H M S F PGM Recording timecode
Page 59 and 60: TC Setup mode details The TC Setup
Page 61 and 62: • Selecting output timecode When
Page 63 and 64: • Catch offset you can capture th
Page 65 and 66: Chapter 6 Storing time data This ch
Page 67 and 68: Storing a time to an edit point mem
Page 69 and 70: Storing a time to a locate point me
Page 71 and 72: • Storing a time to a locate poin
Page 73 and 74: Clearing a CUE or MEMORY point memo
Page 75 and 76: Chapter 7 Locate functions This cha
Page 77 and 78: • Location to the last playback s
Page 79 and 80: • Location to a MEMORY point By s
Page 81 and 82: Chapter 8 Preview function This cha
Page 83 and 84:
• Preview at a locate point You c
Page 85 and 86:
Chapter 9 Audio file management Thi
Page 87 and 88:
• Creating a new file on a disk j
Page 89 and 90:
Editing an audio file name You can
Page 91 and 92:
Restoring a deleted audio file You
Page 93 and 94:
Converting the audio file format Yo
Page 95 and 96:
Combining audio files You can combi
Page 97 and 98:
Chapter 10 Editing track data This
Page 99 and 100:
Tips: SOURCE-PLAY You can monitor t
Page 101 and 102:
Flashing Tips: You can monitor the
Page 103 and 104:
5. Press the [ENTER/YES] key. The u
Page 105 and 106:
4. Press the appropriate edit point
Page 107 and 108:
Chapter 11 Setup mode In the Setup
Page 109 and 110:
You can control the display contras
Page 111 and 112:
Panel lock on/off You can select wh
Page 113 and 114:
4. After entering a desired name, p
Page 115 and 116:
• Showing the router IP address 1
Page 117 and 118:
Showing the main software version Y
Page 119 and 120:
Chapter 12 Utility mode This chapte
Page 121 and 122:
Selecting Rec Protect On or Off You
Page 123 and 124:
Chapter 13 Importing an audio file
Page 125 and 126:
4. Select the desired directory ("b
Page 127 and 128:
9. Click on in the Spot Dialog wind
Page 129 and 130:
Chapter 14 Specifications 14-1
Page 131 and 132:
Pin 5:
Page 133 and 134:
Declaration of EC Directive This eq
show all

audio file in the INSERT mode - Fostex

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?