audio file in the INSERT mode - Fostex

More documents

Recommendations

Info

Pasting track data You can copy track data between the "SOURCE IN" and "SOURCE OUT" points to the clipboard and paste it from the "DEST IN" point on the same or a different track. Paste to the same track Sound data A Sound data A SOURCE IN point SOURCE OUT point DEST IN point Sound data A Paste to the other track Sound data A SOURCE IN point SOURCE OUT point DEST IN point The table below shows the relations among the track modes, selectable source tracks and selectable destination tracks. You can paste data to a different track only when selecting a single track in a STEREO or MULTI (4TR) file as the source track. When selecting 2 or 4 tracks in a STEREO or MULTI (4TR) file, you can paste data only to the same tracks. Track mode MONO mode STEREO mode MULTI (4TR) mode Selectable source tracks track 1 only track 1 or 2 tracks 1 and 2 any one of tracks 1 through 4 any two of tracks 1 through 4 tracks 1 through 4 Selectable destination tracks track 1 track 1 or 2 freely same tracks as the source any one of tracks 1 through 4 freely same 2 tracks as the source same tracks as the source 1. Store the "SOURCE IN", "SOURCE OUT" and "DEST IN" points. See "Chapter 6: Storing time data" for details about how to store edit points. 2. If necessary, trim these edit points using the preview function. See "Chapter 8: Preview function" for details about how to trim edit points. 3. While stopped, press the [AUDIO EDIT] key to show "Copy Clip?" on the display, followed by the [ENTER/YES] key. If you press the [AUDIO EDIT] key once for the first time after turning on the power, "Copy Clip?" is shown on the display. By pressing the [ENTER/YES] key, "Sel.Copy TRK?" appears on the display. Flashing Flashing 4. Press the appropriate edit point key(s) ([SOURCE IN], [SOURCE OUT], [DEST IN] or [DEST OUT] keys) to select the copy source track(s), and press the [ENTER/YES] key. *These edit point keys are used to select tracks 1 through 4 (TR 1 through TR 4), as labeled below the keys. Depending on the track mode of the audio file, the selectable tracks are restricted (see the above). Pressing the [ENTER/YES] key copies data to the clipboard immediately. The display shows "Completed!" momentarily followed by "Clip Paste!". Note that the clipped data also can be used for the cut, erase and insert function. Flashing 10-2
Tips: SOURCE-PLAY You can monitor the track data copied to the clipboard using the SOURCE-PLAY function before carrying out the paste operation. Pressing the [PLAY] key while holding down the [STOP] key caries out the SOURCE-PLAY function, which plays back the track data on the clipboard and stops. After finishing the SOURCE-PLAY, press the [AUDIO EDIT] key to show "Clip Paste?" on the display. 5. While "Clip Paste?" is shown on the display, press the [ENTER/YES] key. "Sel. Paste TRK?" appears on the display, in which you can select the destination track(s) to be pasted. Flashing Flashing 6. If you select a single track as a copy source, select a destination track for paste by pressing the appropriate edit point keys (as step 4) and press the [ENTER/YES] key. If you select 2 or 4 tracks as copy sources, simply press the [ENTER/YES] key again. "Clip Paste" is shown with flashing "Sure?". Flashing Flashing 7. Press the [ENTER/YES] key again. The unit starts pasting the copied track data on the clipboard to the specified track(s) from the "DEST IN" point. The display shows the required time together with the achieved percentage for paste. The time is counted down while the percentage is counted up as the paste operation is in progress. Also, the status is graphically shown by the track 1 level indicators which gradually light up from left to right. When all the data is pasted, "Paste Completed!" is shown and the unit stops. REMAIN H M S % 1 BIT 24 FS 48 2 kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% CLOCK FORMAT -INT- BWF H M S F 1 BIT 24 FS 48 2 kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% CLOCK -INT- FORMAT BWF 1 BIT 24 FS 48 2 kHz ∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1% CLOCK FORMAT -INT- BWF REMAIN H M S % 8. Press the [EXIT/NO] or [STOP] key repeatedly to exit the AUDIO EDIT mode. Tips: If you are not satisfied with the result, you can undo the paste operation. Note that, however, you cannot undo the paste operation with a "Tape mode" audio file. 10-3
Page 1 and 2:
KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 3 and 4:
Table of Contents Chapter-1 Before
Page 5 and 6:
Chapter-9 Audio file management Cre
Page 7 and 8:
Chapter-1 Before using the DV40 Bef
Page 9 and 10:
Setting the internal clock The inte
Page 11 and 12:
Formatting a DVD-RAM disk To make a
Page 13 and 14:
About audio files on a formatted di
Page 15 and 16:
Chapter-2 Names and Functions This
Page 17 and 18:
Front panel part 1 3 4 5 6 7 DVD MA
Page 19 and 20:
c. [PLAY] key Normally, pressing th
Page 21 and 22:
DISP TIME 15. [DISP TIME] key Cycle
Page 23 and 24:
CUE POINT IN DST OUT PREVIEW TR3 TR
Page 25 and 26:
NEW FILE INPUT MON 40. [AUDIO RDY -
Page 27 and 28:
50. [TC GEN MODE] switch Selects th
Page 29 and 30:
4. ETHERNET port ETHERNET 10/100 LI
Page 31 and 32:
Chapter 3 Reformatting/optimizing a
Page 33 and 34:
Tips: How to edit a volume name Whi
Page 35 and 36:
Optimizing a disk By optimizing a u
Page 37 and 38:
Chapter 4 Audio recording/playback
Page 39 and 40:
Recording an analog source in the N
Page 41 and 42:
Recording 1. Press the [RECORD] key
Page 43 and 44:
You can create an audio file before
Page 45 and 46:
Selecting a desired file on a disk
Page 47 and 48: Creating a "Normal mode" audio file
Page 49 and 50: KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 51 and 52: MUTE recording You can make mute re
Page 53 and 54: Cueing by the jog function You can
Page 55 and 56: Chapter 5 Timecode recording This c
Page 57 and 58: ABS H M S F PGM Recording timecode
Page 59 and 60: TC Setup mode details The TC Setup
Page 61 and 62: • Selecting output timecode When
Page 63 and 64: • Catch offset you can capture th
Page 65 and 66: Chapter 6 Storing time data This ch
Page 67 and 68: Storing a time to an edit point mem
Page 69 and 70: Storing a time to a locate point me
Page 71 and 72: • Storing a time to a locate poin
Page 73 and 74: Clearing a CUE or MEMORY point memo
Page 75 and 76: Chapter 7 Locate functions This cha
Page 77 and 78: • Location to the last playback s
Page 79 and 80: • Location to a MEMORY point By s
Page 81 and 82: Chapter 8 Preview function This cha
Page 83 and 84: • Preview at a locate point You c
Page 85 and 86: Chapter 9 Audio file management Thi
Page 87 and 88: • Creating a new file on a disk j
Page 89 and 90: Editing an audio file name You can
Page 91 and 92: Restoring a deleted audio file You
Page 93 and 94: Converting the audio file format Yo
Page 95 and 96: Combining audio files You can combi
Page 97: Chapter 10 Editing track data This
Page 101 and 102: Flashing Tips: You can monitor the
Page 103 and 104: 5. Press the [ENTER/YES] key. The u
Page 105 and 106: 4. Press the appropriate edit point
Page 107 and 108: Chapter 11 Setup mode In the Setup
Page 109 and 110: You can control the display contras
Page 111 and 112: Panel lock on/off You can select wh
Page 113 and 114: 4. After entering a desired name, p
Page 115 and 116: • Showing the router IP address 1
Page 117 and 118: Showing the main software version Y
Page 119 and 120: Chapter 12 Utility mode This chapte
Page 121 and 122: Selecting Rec Protect On or Off You
Page 123 and 124: Chapter 13 Importing an audio file
Page 125 and 126: 4. Select the desired directory ("b
Page 127 and 128: 9. Click on in the Spot Dialog wind
Page 129 and 130: Chapter 14 Specifications 14-1
Page 131 and 132: Pin 5:
Page 133 and 134: Declaration of EC Directive This eq
show all

audio file in the INSERT mode - Fostex

Create successful ePaper yourself

Delete template?

Save as template?