audio file in the INSERT mode - Fostex

More documents

Recommendations

Info

• Location to the point where the recorder located last time You can locate to the point between ABS 0 and REC END where the recorder located last time. 1. When the recorder is stopped, press only the [LOCATE] key. The recorder locates to the point where the recorder located last time. Note that the [LOCATE] key always holds the time data of the point where the recorder located last time. • Location to an audio edit point You can locate to an edit point by pressing the corresponding edit point key ([SOURCE IN], [SOURCE OUT], [DEST IN], or [DEST OUT] key). 1. When the recorder is stopped, press a desired edit point key. The display shows the edit point time assigned to the key you pressed. The display below shows an example when pressing the [SOURCE OUT] key. ABS MEMORY H M S F SF Flashing 2. Press the [LOCATE] key. The recorder locates to the edit point and the display returns to the Normal screen. Tips: You can edit the time shown on the display after carrying out step 1 above. By pressing the [LOCATE] key after editing the time, you can locate to the edited time. See "Chapter 6: Storing time data" for details about how to edit time data. • Location to a CUE point By specifying a desired CUE point memory (among 01 through 99), you can locate to the point. 1. When the recorder is stopped, press the [CUE POINT] key. The display shows a CUE point time with the flashing point number. CUE ABS H M S F SF Flashing 2. Use the jog dial to select a desired CUE point memory (between "01" and "99") and press the [LOCATE] key. The recorder locates to the CUE point and the display returns to the Normal screen. If you select a CUE point memory which does not hold time data, "--H--M--S--F--SF" is shown on the display. Tips: You can edit the time shown on the display after carrying out step 1 above. By pressing the [LOCATE] key after editing the time, you can locate to the edited time. See "Chapter 6: Storing time data" for details about how to edit time data. 7-4
• Location to a MEMORY point By specifying a desired MEMORY point memory (among 04 through 99), you can locate to the point. 1. When the recorder is stopped, press the [MEMORY] key. The display shows a MEMORY point time with the flashing point number. ABS MEMORY H M S F SF Flashing 2. Use the jog dial to select a desired MEMORY point number (between "04" and "99") and press the [LOCATE] key. The recorder locates to the MEMORY point and the display returns to the Normal screen. If you select a MEMORY point which does not hold time data, "--H--M--S--F--SF" is shown on the display. Tips: You can edit the time shown on the display after carrying out step 1 above. By pressing the [LOCATE] key after editing the time, you can locate to the edited time. See "Chapter 6: Storing time data" for details about how to edit time data. • Location to the next or previous CUE/MEMORY point using the skip mode (Skip locate function) By setting the "Skip Mode?" menu in the Setup mode appropriately, you can locate to a CUE or MEMORY point quickly. 1. Set the "Skip Mode?" menu in the Setup mode to "CUE" or "MEM". The "Skip Mode?" menu is initially set to "FILE". See "Chapter 11: Setup mode" for details. 2. Press [SKIP/CURSOR] > key. Each time you press the key, the display shows something like the examples below and the recorder locates the next or previous locate point (CUE or MEMORY point depending on the selection in step 1). • If the skip mode is set to "MEM": ABS MEMORY H M S F SF or ABS MEMORY H M S F SF • If the skip mode is set to "CUE": H M S F SF ABS H M S F SF ABS MEMORY MEMORY or You can locate (including the skip locate function) to a desired time assigned to any of MEMORY points 04 through 99. MEMORY points holding time data can be used in common by all audio files, however, you cannot locate to a MEMORY point which holds a time greater then the REC END time (except for "Tape mode" files). If you are going to locate to a such point, the display shows "Out of Zone!" and the operation is ignored. In the following example, if file 02 is currently selected, you cannot locate to MEMORY 07 or 08. In other words, you can locate to MEMORY points 04 through 06 and 09 through 11. If file 02 is currently selected, you can locate all MEMORY points 04 through 11). Mem 04 Mem 05 Mem 06 Mem 07 Mem 08 File 01 Mem 09 Mem 10 Mem 11 File 02 7-5
Page 1 and 2:
KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 3 and 4:
Table of Contents Chapter-1 Before
Page 5 and 6:
Chapter-9 Audio file management Cre
Page 7 and 8:
Chapter-1 Before using the DV40 Bef
Page 9 and 10:
Setting the internal clock The inte
Page 11 and 12:
Formatting a DVD-RAM disk To make a
Page 13 and 14:
About audio files on a formatted di
Page 15 and 16:
Chapter-2 Names and Functions This
Page 17 and 18:
Front panel part 1 3 4 5 6 7 DVD MA
Page 19 and 20:
c. [PLAY] key Normally, pressing th
Page 21 and 22:
DISP TIME 15. [DISP TIME] key Cycle
Page 23 and 24:
CUE POINT IN DST OUT PREVIEW TR3 TR
Page 25 and 26:
NEW FILE INPUT MON 40. [AUDIO RDY -
Page 27 and 28: 50. [TC GEN MODE] switch Selects th
Page 29 and 30: 4. ETHERNET port ETHERNET 10/100 LI
Page 31 and 32: Chapter 3 Reformatting/optimizing a
Page 33 and 34: Tips: How to edit a volume name Whi
Page 35 and 36: Optimizing a disk By optimizing a u
Page 37 and 38: Chapter 4 Audio recording/playback
Page 39 and 40: Recording an analog source in the N
Page 41 and 42: Recording 1. Press the [RECORD] key
Page 43 and 44: You can create an audio file before
Page 45 and 46: Selecting a desired file on a disk
Page 47 and 48: Creating a "Normal mode" audio file
Page 49 and 50: KEYBOARD MOUSE SOURCE PLAY LOCATE A
Page 51 and 52: MUTE recording You can make mute re
Page 53 and 54: Cueing by the jog function You can
Page 55 and 56: Chapter 5 Timecode recording This c
Page 57 and 58: ABS H M S F PGM Recording timecode
Page 59 and 60: TC Setup mode details The TC Setup
Page 61 and 62: • Selecting output timecode When
Page 63 and 64: • Catch offset you can capture th
Page 65 and 66: Chapter 6 Storing time data This ch
Page 67 and 68: Storing a time to an edit point mem
Page 69 and 70: Storing a time to a locate point me
Page 71 and 72: • Storing a time to a locate poin
Page 73 and 74: Clearing a CUE or MEMORY point memo
Page 75 and 76: Chapter 7 Locate functions This cha
Page 77: • Location to the last playback s
Page 81 and 82: Chapter 8 Preview function This cha
Page 83 and 84: • Preview at a locate point You c
Page 85 and 86: Chapter 9 Audio file management Thi
Page 87 and 88: • Creating a new file on a disk j
Page 89 and 90: Editing an audio file name You can
Page 91 and 92: Restoring a deleted audio file You
Page 93 and 94: Converting the audio file format Yo
Page 95 and 96: Combining audio files You can combi
Page 97 and 98: Chapter 10 Editing track data This
Page 99 and 100: Tips: SOURCE-PLAY You can monitor t
Page 101 and 102: Flashing Tips: You can monitor the
Page 103 and 104: 5. Press the [ENTER/YES] key. The u
Page 105 and 106: 4. Press the appropriate edit point
Page 107 and 108: Chapter 11 Setup mode In the Setup
Page 109 and 110: You can control the display contras
Page 111 and 112: Panel lock on/off You can select wh
Page 113 and 114: 4. After entering a desired name, p
Page 115 and 116: • Showing the router IP address 1
Page 117 and 118: Showing the main software version Y
Page 119 and 120: Chapter 12 Utility mode This chapte
Page 121 and 122: Selecting Rec Protect On or Off You
Page 123 and 124: Chapter 13 Importing an audio file
Page 125 and 126: 4. Select the desired directory ("b
Page 127 and 128: 9. Click on in the Spot Dialog wind
Page 129 and 130:
Chapter 14 Specifications 14-1
Page 131 and 132:
Pin 5:
Page 133 and 134:
Declaration of EC Directive This eq
show all

audio file in the INSERT mode - Fostex

Create successful ePaper yourself

Delete template?

Save as template?