0 Contents - Hilti Svenska AB

More documents

Recommendations

Info

DS Load data Design data Recommended loads Fastening wood to concrete, sandlimemasonry or to steel Fastening wood to concrete, sandlimemasonry: Nrec = Vrec = 400 N Fastening wood to steel: Design conditions: • For safety relevant fastenings sufficient redundancy of the entire system is required: Minimum 5 fastenings per fastened unit with normal weight concrete base material. • Increase to 600 N possible if 8 or more fastenings in each fastened unit. • All visible failures must be replaced. • Valid for concrete and sand lime-masonry with strength of fcc < 40 N/mm2 Nrec = Vrec = 600 N Nrec Vrec . • Fastened material: wood, minimum thickness = 24 mm plywood, minimum thickness = 16 mm Soft material: • Working loads depend on strength and thickness of material fastened. Do not use working loads in excess of those for wood. • Depth penetration and other conditions same as for fastening wood. • Use R23 or R36 (∅ 4.5 mm hole) washer to control penetration and to increase pullover strength. Separately available from <strong>Hilti</strong>. Metal profiles to concrete: Nrec Vrec Nrec = Vrec = 400 N • Minimum 5 fastenings per fastened unit (normal weight concrete) • Increase to 600 N possible if 8 or more fastenings in each fastened unit. • All visible failures must be replaced • tI = 1–4 mm Test data For more detailed information on the performance of the system please contact <strong>Hilti</strong>. 4.136 11 / 2007
Application requirements Thickness of base material hmin Concrete dnom hmin = 100 mm (dnom ≥ 4.5 mm) Thickness of fastened material tI ≤ 50.0 mm Spacing and edge distances (mm) Steel tll ≥ 6 mm Edge distance: concrete Edge distance: concrete 80 Spacing on wood Spacing, edge distances on steel Corrosion information The intended use for safety relevant and permanent applications only comprises fastenings which are not directly exposed to external weather conditions or moist atmospheres. For further detailed information on corrosion see corresponding chapter in section Direct Fastening Technology. 11 / 2007 4.137 15 tII DS
Page 1 and 2:
Contents Product index DX / GX fast
Page 3 and 4:
Product Index DX/GX Fastener Design
Page 5 and 6:
X-ENP Siding and Decking Nail Produ
Page 7 and 8:
Recommended loads - Aluminum sheeti
Page 9 and 10:
Spacing and edge distances (mm) Ste
Page 11 and 12:
Cartridge selection and tool energy
Page 13 and 14:
X-ENP 2K Siding and Decking Nail Pr
Page 15 and 16:
Thickness of fastened material Shee
Page 17 and 18:
Cartridge selection and tool energy
Page 19 and 20:
SDK2 Sealing Caps for Cladding Fast
Page 21 and 22:
NPH Siding and Decking Nails to Con
Page 23 and 24:
Thickness of fastened material Shee
Page 25 and 26:
Installation Pre-drill with TX-C-5/
Page 27 and 28:
X-HVB Shear Connectors Product data
Page 29 and 30:
Reduction factors for profile metal
Page 31 and 32:
Connector positioning, spacing and
Page 33 and 34:
Recommended setting range Applicati
Page 35 and 36:
X-EDNK 22 THQ 12, X-EDN 19 THQ 12 D
Page 37 and 38:
Application requirements Thickness
Page 39 and 40:
Fastener selection and system recom
Page 41 and 42:
X-EDNI, EDS X-EDNI, EDS General Pur
Page 43 and 44:
Application Requirements Thickness
Page 45 and 46:
Fastener selection Cartridge recomm
Page 47 and 48:
X-BT Stainless Steel Threaded Studs
Page 49 and 50:
Page 51 and 52:
1. Mark location for each fastening
Page 53 and 54:
M6/W6 o 3.7 o 3.8 o 8 1.7 Lg L Ls X
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
X-FCM Grating Fastening System Prod
Page 61 and 62:
X-FCM-R mean ultimate Vu,m and char
Page 63 and 64:
X-FCM Fastener selection and system
Page 65 and 66:
Fastening Quality Assurance Fasteni
Page 67 and 68:
X-GR Grating Fastening System Produ
Page 69 and 70:
Spacing and edge distances Edge dis
Page 71 and 72:
X-GR RU Grating Fastening System Pr
Page 73 and 74:
Spacing and edge distances Edge dis
Page 75 and 76:
X-MGR Grating Fastening System Prod
Page 77 and 78:
Grating opening types a b c Fastene
Page 79 and 80:
X-FCP Checker Plate Fastening Syste
Page 81 and 82:
Recommended setting range DX 76 DX
Page 83 and 84:
Installation Installation procedure
Page 85 and 86: X-U General Purpose Nails for Concr
Page 87 and 88: Fastenings to steel Design data Fas
Page 89 and 90: Condition for thick fastened steel
Page 91 and 92: Fastener program Standard Tools Spe
Page 93 and 94: Fastening quality assurance Fasteni
Page 95 and 96: X-AL-H General Purpose Nails Produc
Page 97 and 98: Application requirements Thickness
Page 99 and 100: Fastening wood or soft material Woo
Page 101 and 102: X-DNI General Purpose Nails for Con
Page 105 and 106: Fastener selection and system recom
Page 107 and 108: Fasteners Tool Designation Item no
Page 109 and 110: X-ZF General Purpose Nails for Conc
Page 113 and 114: System recommendation Fasteners Too
Page 115 and 116: X-CR Stainless Steel Nails for Conc
Page 117 and 118: Test data Important note: Test data
Page 119 and 120: Fastener selection Fastener selecti
Page 123 and 124: DX Drywall Fasteners DX Drywall Fas
Page 125 and 126: Spacing and edge distances (mm) Spa
Page 127 and 128: Cartridge selection and tool energy
Page 129 and 130: GX Drywall Fasteners GX Drywall Fas
Page 135: DS Heavy Duty General Purpose Nails
Page 139 and 140: Fastening metal profiles Required n
Page 141 and 142: SL Nails for Forming or other Tempo
Page 143 and 144: Spacing and edge distance (mm) Corr
Page 145 and 146: X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 147 and 148: X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 149 and 150: System recommendation Fasteners Too
Page 151 and 152: DX-Kwik X-M 6H, X-M 8H Threaded Stu
Page 153 and 154: DX Kwik Nail Characteristic Concret
Page 155 and 156: Installation X-M6H, X-M8H DNH 37, X
Page 157 and 158: X-CRM X-CR M Stainless Steel Thread
Page 159 and 160: Arrangements to reduce or prevent m
Page 161 and 162: Recommended setting range X-CRM Cor
Page 165 and 166: X-IE Wall Insulation Fastener Produ
Page 167 and 168: Recommended setting range Concrete:
Page 169 and 170: X-SW 30, X-SW 60 X-SW 30, X-SW 60 S
Page 173 and 174: X-FS Form Stop Product data Dimensi
Page 177 and 178: X-HS Threaded Hanger and X-CC Loop
Page 179 and 180: DX Standard (without pre-drilling)
Page 181 and 182: Fastener selection X-HS, X-CC Progr
Page 183 and 184: X-HSMX, X-CCMX Electrical Hanger Sy
Page 187 and 188:
Fastening quality assurance Install
Page 189 and 190:
X-EKB, X-ECH X-EKB, X-ECH Electrica
Page 191 and 192:
X-ECH: Laying cable on ceilings and
Page 193 and 194:
Page 195 and 196:
Fastener selection: Order informati
Page 197 and 198:
X-FB, X-DFB, X-EMTC, X-FBMX X-FB (X
Page 199 and 200:
Page 201 and 202:
Material specification: ➀ Polyeth
Page 203 and 204:
Fastening quality assurance Fasteni
Page 205 and 206:
X-ECTMX, X-EKSMX, X-EMTSC X-ECT MX
Page 207 and 208:
Fastenings to steel Average tensile
Page 209 and 210:
X-EKS Item no. Designation 285719 X
Page 211 and 212:
X-ET for Fastening Plastic Electric
Page 213 and 214:
Page 215 and 216:
System recommendation Fastening qua
Page 217 and 218:
Special X-CR Stainless Steel Nails
Page 219 and 220:
Special X-CR Test data For more det
Page 221 and 222:
Fastening quality assurance Fasteni
Page 223 and 224:
DX 460 General Purpose Tool DX 460-
Page 225 and 226:
Fastener guide: X-460-F8SS S12 fast
Page 227 and 228:
DX 351 DX 351 with X-MX27 Interior
Page 229 and 230:
DX E72 DX E72 Fastener: X-U X-EDNI,
Page 231 and 232:
DX 76 / DX 76 PTR DX 76 PTR (Siding
Page 233 and 234:
DX 76 F15 (Siding and decking on co
Page 235 and 236:
DX-860 Tool for Decking DX 860-ENP
Page 237 and 238:
Tools and equipment GX 120 Gas Tool
show all

0 Contents - Hilti Svenska AB

Create successful ePaper yourself

Delete template?

Save as template?