0 Contents - Hilti Svenska AB

More documents

Recommendations

Info

X-EKB, X-ECH General information Material specification See Fastener selection Fastening tools DX 460-F8, DX 351-F8, GX 120-ME, GX 100-E, DX 460 MX, DX 351 MX See fastener selection for more details. Approvals CSTB (France): X-EKB 8/X-EKB 16 with X-DNI-H 37 X-ECH with X-DNI-H 37 Note: Technical data presented in these approvals and design guidelines reflect specific local conditions and may differ from those published in this handbook. Applications Examples X-EKB for fastening cables to concrete X-ECH for fastening bunched cables Load data Design data X-EKB: Securing electrical cables to concrete ceilings and walls Max. capacity (number of cables in one X-EKB) at spacing of 50–100 mm Number of wires/cables and wire sizes Designation NYM 3 x 1.5 mm 2 (∅ 8 mm) NYM 5 x 1.5 mm 2 (∅ 10 mm) X-EKB 4 __ 4 3 X-EKB 8 __ 8 5 X-EKB 16 __ 16 10 4.190 11 / 2007
X-ECH: Laying cable on ceilings and walls Max. capacity (Number of ∅ 10 mm cables / X-ECH) at spacing of 60–80 mm Designation Number of cables X-ECH-S __ and X-ECH/FR-S __ 10–15 X-ECH-M __ and X-ECH/FR-M __ 20–25 X-EKB, X-ECH X-ECH-L __ and X-ECH/FR-L __ 30–35 Conditions: • For concrete C12/15 to C45/55 (fcc ″ 15 N/mm2 to 55 N/mm2 / fc ″ 12 N/mm2 to 45 N/mm2 ), aggregate size < 32 mm • All visible placing failures have to replaced • Damaged X-ECH have to replaced Test data Important note: Test data are for information only and can’t be used for design. These data are examples and not representing the whole range of applications and load cases. Design data for <strong>Hilti</strong> standard nails in concrete are based on a specific statistical evaluation method taken into consideration high variation coefficients. The evaluation procedure is described within section Direct Fastening Technology of this manual. For more detailed information please contact <strong>Hilti</strong>. Load capacity of the nails: Fastenings to concrete Average tensile Scatter Embedment Concrete failure load depth strength Nail Nu,m [kN] [%] hET [mm] fcc [N/mm 2 ] X-U 37 PH 1.53 56.4 17.0 31.5 X-U 22 MX 3.18 37.8 20.1 54.7 X-U 27 MX 4.04 35.4 24.5 30.9 X-GHP 20 MX 1.61 52.0 14.0 52.2 X-GN 27 MX 1.91 47.1 19.2 23.7 Fastenings to steel Average tensile Scatter Embedment Steel Steel failure load depth thickness strength Nail Nu,m [kN] [%] hET [mm] tll [mm] fu [N/mm 2 ] X-U 16 MX 17.46 4.0 12.2 6 634 X-EGN 14 MX 3.62 13.7 8.6 6 543 11 / 2007 4.191
Page 1 and 2:
Contents Product index DX / GX fast
Page 3 and 4:
Product Index DX/GX Fastener Design
Page 5 and 6:
X-ENP Siding and Decking Nail Produ
Page 7 and 8:
Recommended loads - Aluminum sheeti
Page 9 and 10:
Spacing and edge distances (mm) Ste
Page 11 and 12:
Cartridge selection and tool energy
Page 13 and 14:
X-ENP 2K Siding and Decking Nail Pr
Page 15 and 16:
Thickness of fastened material Shee
Page 17 and 18:
Page 19 and 20:
SDK2 Sealing Caps for Cladding Fast
Page 21 and 22:
NPH Siding and Decking Nails to Con
Page 23 and 24:
Thickness of fastened material Shee
Page 25 and 26:
Installation Pre-drill with TX-C-5/
Page 27 and 28:
X-HVB Shear Connectors Product data
Page 29 and 30:
Reduction factors for profile metal
Page 31 and 32:
Connector positioning, spacing and
Page 33 and 34:
Recommended setting range Applicati
Page 35 and 36:
X-EDNK 22 THQ 12, X-EDN 19 THQ 12 D
Page 37 and 38:
Application requirements Thickness
Page 39 and 40:
Fastener selection and system recom
Page 41 and 42:
X-EDNI, EDS X-EDNI, EDS General Pur
Page 43 and 44:
Application Requirements Thickness
Page 45 and 46:
Fastener selection Cartridge recomm
Page 47 and 48:
X-BT Stainless Steel Threaded Studs
Page 49 and 50:
Page 51 and 52:
1. Mark location for each fastening
Page 53 and 54:
M6/W6 o 3.7 o 3.8 o 8 1.7 Lg L Ls X
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
X-FCM Grating Fastening System Prod
Page 61 and 62:
X-FCM-R mean ultimate Vu,m and char
Page 63 and 64:
X-FCM Fastener selection and system
Page 65 and 66:
Fastening Quality Assurance Fasteni
Page 67 and 68:
X-GR Grating Fastening System Produ
Page 69 and 70:
Spacing and edge distances Edge dis
Page 71 and 72:
X-GR RU Grating Fastening System Pr
Page 73 and 74:
Spacing and edge distances Edge dis
Page 75 and 76:
X-MGR Grating Fastening System Prod
Page 77 and 78:
Grating opening types a b c Fastene
Page 79 and 80:
X-FCP Checker Plate Fastening Syste
Page 81 and 82:
Recommended setting range DX 76 DX
Page 83 and 84:
Installation Installation procedure
Page 85 and 86:
X-U General Purpose Nails for Concr
Page 87 and 88:
Fastenings to steel Design data Fas
Page 89 and 90:
Condition for thick fastened steel
Page 91 and 92:
Fastener program Standard Tools Spe
Page 93 and 94:
Fastening quality assurance Fasteni
Page 95 and 96:
X-AL-H General Purpose Nails Produc
Page 97 and 98:
Page 99 and 100:
Fastening wood or soft material Woo
Page 101 and 102:
X-DNI General Purpose Nails for Con
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Fasteners Tool Designation Item no
Page 109 and 110:
X-ZF General Purpose Nails for Conc
Page 111 and 112:
Page 113 and 114:
System recommendation Fasteners Too
Page 115 and 116:
X-CR Stainless Steel Nails for Conc
Page 117 and 118:
Test data Important note: Test data
Page 119 and 120:
Fastener selection Fastener selecti
Page 121 and 122:
Page 123 and 124:
DX Drywall Fasteners DX Drywall Fas
Page 125 and 126:
Spacing and edge distances (mm) Spa
Page 127 and 128:
Page 129 and 130:
GX Drywall Fasteners GX Drywall Fas
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
DS Heavy Duty General Purpose Nails
Page 137 and 138:
Page 139 and 140: Fastening metal profiles Required n
Page 141 and 142: SL Nails for Forming or other Tempo
Page 143 and 144: Spacing and edge distance (mm) Corr
Page 145 and 146: X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 147 and 148: X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 149 and 150: System recommendation Fasteners Too
Page 151 and 152: DX-Kwik X-M 6H, X-M 8H Threaded Stu
Page 153 and 154: DX Kwik Nail Characteristic Concret
Page 155 and 156: Installation X-M6H, X-M8H DNH 37, X
Page 157 and 158: X-CRM X-CR M Stainless Steel Thread
Page 159 and 160: Arrangements to reduce or prevent m
Page 161 and 162: Recommended setting range X-CRM Cor
Page 163 and 164: Fastening quality assurance Fasteni
Page 165 and 166: X-IE Wall Insulation Fastener Produ
Page 167 and 168: Recommended setting range Concrete:
Page 169 and 170: X-SW 30, X-SW 60 X-SW 30, X-SW 60 S
Page 171 and 172: Fastener selection and system recom
Page 173 and 174: X-FS Form Stop Product data Dimensi
Page 177 and 178: X-HS Threaded Hanger and X-CC Loop
Page 179 and 180: DX Standard (without pre-drilling)
Page 181 and 182: Fastener selection X-HS, X-CC Progr
Page 183 and 184: X-HSMX, X-CCMX Electrical Hanger Sy
Page 185 and 186: Application requirements Thickness
Page 187 and 188: Fastening quality assurance Install
Page 189: X-EKB, X-ECH X-EKB, X-ECH Electrica
Page 195 and 196: Fastener selection: Order informati
Page 197 and 198: X-FB, X-DFB, X-EMTC, X-FBMX X-FB (X
Page 201 and 202: Material specification: ➀ Polyeth
Page 205 and 206: X-ECTMX, X-EKSMX, X-EMTSC X-ECT MX
Page 207 and 208: Fastenings to steel Average tensile
Page 209 and 210: X-EKS Item no. Designation 285719 X
Page 211 and 212: X-ET for Fastening Plastic Electric
Page 215 and 216: System recommendation Fastening qua
Page 217 and 218: Special X-CR Stainless Steel Nails
Page 219 and 220: Special X-CR Test data For more det
Page 223 and 224: DX 460 General Purpose Tool DX 460-
Page 225 and 226: Fastener guide: X-460-F8SS S12 fast
Page 227 and 228: DX 351 DX 351 with X-MX27 Interior
Page 229 and 230: DX E72 DX E72 Fastener: X-U X-EDNI,
Page 231 and 232: DX 76 / DX 76 PTR DX 76 PTR (Siding
Page 233 and 234: DX 76 F15 (Siding and decking on co
Page 235 and 236: DX-860 Tool for Decking DX 860-ENP
Page 237 and 238: Tools and equipment GX 120 Gas Tool
show all

0 Contents - Hilti Svenska AB

Create successful ePaper yourself

Delete template?

Save as template?