0 Contents - Hilti Svenska AB

More documents

Recommendations

Info

X-BT Fastener selection Fasteners Tool Designation Item no. Designation X-BT M8-15-6 SN12-R 377074 DX 351-BT/ BTG X-BT M10-24-6 SN12-R 377078 DX 351-BT/ BTG X-BT W10-24-6 SN12-R 377076 DX 351-BT/ BTG X-BT M8 without washer 377073 DX 351-BT/ BTG X-BT M10 without washer 377077 DX 351-BT/ BTG X-BT W10 without washer 377075 DX 351-BT/ BTG Cartridge selection and tool energy setting 6.8/11 M high precession brown cartridge Fine adjustment by installation tests on site Fastening quality assurance Fastening inspection hNVS X-BT M8 hNVS = 15.7–16.8 mm X-BT M10 / X-BT W10 hNVS = 25.7–26.8 mm Installation X-BT with washer X-BT without washer Fastened material hole ∅ ≥ 13 mm Fastened material hole ∅ ≥ 11 mm for X-BT M/W10 ≥ 9 mm for X-BT M8 4.50 11 / 2007
1. Mark location for each fastening 2. Pre-drill with TX-BT 4/7 step shank drill bit A Pre-drill until the shoulder grinds a shiny ring (to assure proper drilling depth) Before fastener installation: The drilled hole must be clear of liquids and debris. The area around the drilled hole must be free from liquids and debris. 3. Drive X-BT-R studs into drilled hole 51 Adjust power on DX 351 BT so that the fastener standoff hNVS, is not greater than: hNVS ≤ 26.8 mm (X-BT M/W10....-R) hNVS ≤ 16.8 mm (X-BT M8…-R) hNVS 3 2 1 4. Hang unit on studs. Put on washers and hand tighten nuts Sealing washer must be properly compressed! 5. Tighten using a screwdriver with torque clutch X-BT Tightening torque: Trec ≤ 8 Nm (5.9 ft-lb)! 11 / 2007 4.51 Trec <strong>Hilti</strong> Torque screwdriver: setting: SF 121-A 11 SF 150-A 9 SF 180-A 8
Page 1 and 2: Contents Product index DX / GX fast
Page 3 and 4: Product Index DX/GX Fastener Design
Page 5 and 6: X-ENP Siding and Decking Nail Produ
Page 7 and 8: Recommended loads - Aluminum sheeti
Page 9 and 10: Spacing and edge distances (mm) Ste
Page 11 and 12: Cartridge selection and tool energy
Page 13 and 14: X-ENP 2K Siding and Decking Nail Pr
Page 15 and 16: Thickness of fastened material Shee
Page 17 and 18: Cartridge selection and tool energy
Page 19 and 20: SDK2 Sealing Caps for Cladding Fast
Page 21 and 22: NPH Siding and Decking Nails to Con
Page 23 and 24: Thickness of fastened material Shee
Page 25 and 26: Installation Pre-drill with TX-C-5/
Page 27 and 28: X-HVB Shear Connectors Product data
Page 29 and 30: Reduction factors for profile metal
Page 31 and 32: Connector positioning, spacing and
Page 33 and 34: Recommended setting range Applicati
Page 35 and 36: X-EDNK 22 THQ 12, X-EDN 19 THQ 12 D
Page 37 and 38: Application requirements Thickness
Page 39 and 40: Fastener selection and system recom
Page 41 and 42: X-EDNI, EDS X-EDNI, EDS General Pur
Page 43 and 44: Application Requirements Thickness
Page 45 and 46: Fastener selection Cartridge recomm
Page 47 and 48: X-BT Stainless Steel Threaded Studs
Page 49: Application requirements Thickness
Page 53 and 54: M6/W6 o 3.7 o 3.8 o 8 1.7 Lg L Ls X
Page 57 and 58: Fastener selection and system recom
Page 59 and 60: X-FCM Grating Fastening System Prod
Page 61 and 62: X-FCM-R mean ultimate Vu,m and char
Page 63 and 64: X-FCM Fastener selection and system
Page 65 and 66: Fastening Quality Assurance Fasteni
Page 67 and 68: X-GR Grating Fastening System Produ
Page 69 and 70: Spacing and edge distances Edge dis
Page 71 and 72: X-GR RU Grating Fastening System Pr
Page 73 and 74: Spacing and edge distances Edge dis
Page 75 and 76: X-MGR Grating Fastening System Prod
Page 77 and 78: Grating opening types a b c Fastene
Page 79 and 80: X-FCP Checker Plate Fastening Syste
Page 81 and 82: Recommended setting range DX 76 DX
Page 83 and 84: Installation Installation procedure
Page 85 and 86: X-U General Purpose Nails for Concr
Page 87 and 88: Fastenings to steel Design data Fas
Page 89 and 90: Condition for thick fastened steel
Page 91 and 92: Fastener program Standard Tools Spe
Page 93 and 94: Fastening quality assurance Fasteni
Page 95 and 96: X-AL-H General Purpose Nails Produc
Page 99 and 100: Fastening wood or soft material Woo
Page 101 and 102:
X-DNI General Purpose Nails for Con
Page 103 and 104:
Application requirements Thickness
Page 105 and 106:
Fastener selection and system recom
Page 107 and 108:
Fasteners Tool Designation Item no
Page 109 and 110:
X-ZF General Purpose Nails for Conc
Page 111 and 112:
Page 113 and 114:
System recommendation Fasteners Too
Page 115 and 116:
X-CR Stainless Steel Nails for Conc
Page 117 and 118:
Test data Important note: Test data
Page 119 and 120:
Fastener selection Fastener selecti
Page 121 and 122:
Fastening quality assurance Fasteni
Page 123 and 124:
DX Drywall Fasteners DX Drywall Fas
Page 125 and 126:
Spacing and edge distances (mm) Spa
Page 127 and 128:
Cartridge selection and tool energy
Page 129 and 130:
GX Drywall Fasteners GX Drywall Fas
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
DS Heavy Duty General Purpose Nails
Page 137 and 138:
Page 139 and 140:
Fastening metal profiles Required n
Page 141 and 142:
SL Nails for Forming or other Tempo
Page 143 and 144:
Spacing and edge distance (mm) Corr
Page 145 and 146:
X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 147 and 148:
X-M6, X-W6, X-F7, X-M8, X-M10, X-W1
Page 149 and 150:
System recommendation Fasteners Too
Page 151 and 152:
DX-Kwik X-M 6H, X-M 8H Threaded Stu
Page 153 and 154:
DX Kwik Nail Characteristic Concret
Page 155 and 156:
Installation X-M6H, X-M8H DNH 37, X
Page 157 and 158:
X-CRM X-CR M Stainless Steel Thread
Page 159 and 160:
Arrangements to reduce or prevent m
Page 161 and 162:
Recommended setting range X-CRM Cor
Page 163 and 164:
Page 165 and 166:
X-IE Wall Insulation Fastener Produ
Page 167 and 168:
Recommended setting range Concrete:
Page 169 and 170:
X-SW 30, X-SW 60 X-SW 30, X-SW 60 S
Page 171 and 172:
Page 173 and 174:
X-FS Form Stop Product data Dimensi
Page 175 and 176:
Page 177 and 178:
X-HS Threaded Hanger and X-CC Loop
Page 179 and 180:
DX Standard (without pre-drilling)
Page 181 and 182:
Fastener selection X-HS, X-CC Progr
Page 183 and 184:
X-HSMX, X-CCMX Electrical Hanger Sy
Page 185 and 186:
Page 187 and 188:
Fastening quality assurance Install
Page 189 and 190:
X-EKB, X-ECH X-EKB, X-ECH Electrica
Page 191 and 192:
X-ECH: Laying cable on ceilings and
Page 193 and 194:
Page 195 and 196:
Fastener selection: Order informati
Page 197 and 198:
X-FB, X-DFB, X-EMTC, X-FBMX X-FB (X
Page 199 and 200:
Page 201 and 202:
Material specification: ➀ Polyeth
Page 203 and 204:
Page 205 and 206:
X-ECTMX, X-EKSMX, X-EMTSC X-ECT MX
Page 207 and 208:
Fastenings to steel Average tensile
Page 209 and 210:
X-EKS Item no. Designation 285719 X
Page 211 and 212:
X-ET for Fastening Plastic Electric
Page 213 and 214:
Page 215 and 216:
System recommendation Fastening qua
Page 217 and 218:
Special X-CR Stainless Steel Nails
Page 219 and 220:
Special X-CR Test data For more det
Page 221 and 222:
Page 223 and 224:
DX 460 General Purpose Tool DX 460-
Page 225 and 226:
Fastener guide: X-460-F8SS S12 fast
Page 227 and 228:
DX 351 DX 351 with X-MX27 Interior
Page 229 and 230:
DX E72 DX E72 Fastener: X-U X-EDNI,
Page 231 and 232:
DX 76 / DX 76 PTR DX 76 PTR (Siding
Page 233 and 234:
DX 76 F15 (Siding and decking on co
Page 235 and 236:
DX-860 Tool for Decking DX 860-ENP
Page 237 and 238:
Tools and equipment GX 120 Gas Tool
show all

0 Contents - Hilti Svenska AB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?