Installation Notes - USP Connectors

PANEL HANGERS – FHD26
FHD – Straddles the header and receives a joist from both sides.
Materials: 18 gauge
Finish: G90 galvanizing
Installation:
• Use all specified fasteners. See Product Notes, page 10.
• In panelized construction, installers are allowed to nail through
both the sheathing and the hanger top flange with (1) 10d nail.
The nail should be centered in the top flange and be no closer
than 1/4˝ from the back or front edge of the top flange.
NEW
Dimensions (in)
Fastener Schedule 3,5
Factored Resistance
Header
Joist
DF-L
S-P-F
Joist USP
Steel
Top Face Uplift 2 Uplift 2
Size Stock No. Ref. No. Gauge W H D TF 4 Qty Qty Type Qty Type Unit 100% 115% 100% 115%
Lbs 1575 335 1120 235
FHD26 -- -- 18 5-3/8 1-1/2 specify 2 2 2 10d x 1-1/2
kN 7.01 1.49 4.98 1.05
1) Loads listed are per side.
2) Factored resistances have been increased 15% for short-term loads such as wind and earthquake; reduce for other load durations in accordance with the code.
3) Minimum nail embedment shall be 8 nail diameters (typ).
4) "Specify" denotes the required top flange width that must be specified at the time of ordering.
5) NAILS:
New products or updated product information are designated in red font.
PURLIN HANGERS – JPF SERIES
W
3 3 /4˝
H
D
FHD
TF
© Copyright 2013 USP Structural Connectors ®
Materials: 20 gauge
Finish: G90 galvanizing
Options: JPF24 and JPF26 are available
in Triple Zinc. To order, add TZ to
stock number, as in JPF24-TZ.
Codes: Load values are derived from
data submitted to various North
American building code evaluators.
Installation:
• Use all specified fasteners. See Product Notes, page
10.
• Diamond holes allow optional header nailing.
• Joist nails must be driven at a 30° to 45° angle
through the purlin into the header to achieve listed
loads. Standard length “double shear” nails must
be used to achieve listed load values.
• 16d sinkers (9 gauge x 3 1/4˝) may be used where
10d commons are specified with no load reduction.
Raised
dimple allows
30º to 45˚
nailing
Typical JPF24
installation
W 1 1/2˝
JPF24
NEW
H
TF
Typical JPF24
back-to-back installation
Double shear nail
design features
fewer nails and
faster installation
Uses standard
length nails
Hangers
Purlin
Size
USP
Stock No.
JPF24
JPF26 PF26 20
Dimensions (in) Fastener Schedule 3,4
Factored Resistance
Header 2 Joist DF-L (Lbs) DF-L (kN) S-P-F (Lbs) S-P-F (kN)
Steel
Top Face Floor Uplift 1 Floor Uplift 1 Floor Uplift 1 Floor Uplift 1
Ref. No. Gauge W H TF Qty Qty Type Qty Type 100% 115% 100% 115% 100% 115% 100% 115%
PF24 20 1-9/16
1-9/16
3-3/8
5-3/8
1-1/16
1-1/16
2
2
-- --
-- --
10d
10d
2
2
10d
10d
1755
1755
675
675
7.81
7.81
3.00
3.00
1245
1245
480
480
5.54
5.54
2.14
2.14
2
2
2
2
10d
10d
2
2
10d
10d
1995
1995
890
890
8.87
8.87
3.96
3.96
1420
1420
630
630
6.32
6.32
2.80
2.80
1) Factored resistances have been increased 15% for short-term loads such as wind and earthquake; reduce for other load durations in accordance with the code.
2) JPF cannot be used back to back on a single ply header when optional nailing is used.
3) Minimum nail embedment shall be 8 nail diameters (typ).
4) NAILS:
New products or updated product information are designated in red font.
110
1-800-328-5934 • www.USPconnectors.com