Installation Notes - USP Connectors

Heavy-Duty Face Mount Hangers – HD series
HD hangers are heavy-duty face mount hangers that can be
used to support headers, joists, and trusses.
Materials: 14 gauge
Finish: G90 galvanizing
Options: HD28-2IF, HD210-2IF, HD210-3IF, HD44IF,
HD46, HD46IF, HD48, HD48IF, HD410,
HD410IF, HD412, HD412IF, HD68, HD68IF,
HD610, HD610IF, HD612 & HD612IF are
available in Triple Zinc. To order, add TZ to
stock number, as in HD28-2IFTZ.
HD210-2IF is available in Stainless Steel. To
order, add SS to stock number,
as in HD210-2IFSS.
All nominal lumber sizes are available
rough/full size lumber. See Specialty Options
Chart.
Codes: Load values are derived from data submitted to
various North American building code
evaluators.
Installation:
• Use all specified fasteners. See Product Notes, page 10.
• Some HD models feature nail holes along bend line that must
be filled to achieve factored resistance. Verify proper
header width to accomplish this for inverted models.
Typical HD610
installation
W
Bend line
nailing
HD610
A
D
H
Typical HD210-2
installation
Drive bend line nails
into header at 45°
to achieve listed loads.
© Copyright 2013 USP Structural Connectors ®
Specialty Options Chart – refer to Specialty Options
pages 210 to 211 for additional details.
Option 4 Skewed 1,3 Sloped Seat 2,3 Sloped / Skewed 1,2,3 Inverted Flange
Range
Factored
Resistance
Ordering
when width is
100% of table value.
75% of uplift value
on skews greater
Add SK, angle required,
and right (R) or left (L),
to product number.
Ex. HD410-SK45R
100% of table value
Add SL, slope required,
and up (U) or down (D),
to product number.
Ex. HD410-SL30D
See Sloped Seat and
Skewed
80% of table value.
75% of uplift value
on skews greater
See Sloped Seat and
Skewed.
Ex. HD410-SK45RSL30D
Not available in
100% of table value.
65% of table value when
nailing into the support
members end grain.
Add IF
to product number.
Ex. HD410IF
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) All sloped, skewed, or combinations require bevel cut on joist in all applications and web stiffeners with I-joists.
4) Modifications of HD hangers may be manufactured as hot rolled, welded, or primed.
Inverted Flange Hangers – HDQIF series
HDQIF inverted flange hangers install with wood screws eliminating
the need to drill bolt holes simplifying installation.
Typical HD210-2IF
inverted flange
installation
Typical HD3212
glulam installation
W
A
HD51135
D
H
Hangers
Materials: 14 gauge
Finish: G90 galvanizing
Options: HDQ612IF is available in Stainless Steel. To order,
add SS to stock number, as in HDQ612IF-SS.
Codes: Load values are derived from data submitted to
various North American building code evaluators.
H
90
Installation:
• Use all specified fasteners. See Product Notes, page 10.
• WS15 and WS3 Wood Screws are supplied with HDQIF hangers.
1-800-328-5934 • www.USPconnectors.com
W
HDQIF
3˝
Up to
3/4˝ gap
Typical HDQIF
installation