workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

More documents

Recommendations

Info

LEHÚZATÓ- ÉS VEZET� CSAVAROK PULLER PULLER AND AND PILOT PILOT BOLTS BOLTS FEJE- ZET SECTION SECTION Törzsszám Stock Stock No.: No.: RAJZSZÁM DRW. Draw. NO. NO. MEGNEVEZÉS DESCRIPTION FELHASZNÁLÁS APPLICATION 213, 213, 313 313 902390 902390 M12x40 M12X40 ISO 4017-10.9 ISO 4017-10.9 Hatlapfej� tövigm.csavar (4 Hex. db) full thrd. bolt, (4 off) Hex. full thrd. bolt, (4 off) Fékdobhoz For brake drum 220 910186 M8x25 Hatlapfej� tövigm.csavar (2 Bolygótartóhoz és a peremes 220 910186 ISO M8X25 4017-10.9 ISO 4017-10.9 db) Hex. full thrd. bolt, (2 off) Hex. full thrd. bolt, (2 off) koronás For planet anyához carrier and flanged For castle planet nut carrier and flanged castle nut 282, 923737 M12x30 Ászokcsavar (2 db) Hajtóm� beszereléséhez 289, 289, 312, 316 312, 316 923737 MSZ M12X30 2402-10.9 MSZ 2402-10.9 Stud bolt, (2 off) Std bolt, (2 off) For installing differential For installing differential carrier carrier 283 283 987548 987548 M8-10 M8-10 ISO 4032 ISO 4032 Hatlapú anya (4 db) Hex. nut, (4 off) Kapcsolóagyhoz For companion flange 288, 315 288, 315 24 M12X1,5x80 ISO M12X1.5X80 8676-10.9 ISO 8676-10.9 Hatlapfej� tövigm.csavar (4 db) Hex. full thrd. bolt, (4 off) Hex. full thrd. bolt, (4 off) 939037 M12 MSZ 2201 Alátét (4 db) 939037 M12 MSZ 2201 Washer, (4 (4 off) 365244 M12X1,5 M12X1.5 365244 ISO 8673-8 ISO 8673-8 316 910339 M12x65 316 910339 ISO M12X65 4017-10.9 ISO 4017-10.9 SECTION 208. PULLER AND PILOT BOLTS Hatlapú anya (4 db) Hex. nut, (4 off) Hatlapfej� tövigm.csavar (2 db) Hex. full thrd. bolt, (2 off) Hex. full thrd. bolt, (2 off) 208 Tányérkerék felhúzatásához For pulling on the driver drive gear Csapágyhüvely kiszereléséhez For removing the bearing cage For removing the bearing cage
This section summarizes the service operations and adjustment data considered by us to be most important and which should thoroughly be observed and followed during assembling the axle. WHEEL DRIVE AND THE WHEEL HUB Assure 0.01 - 0.04 mm axial play for the wheel hub bearings after securing the spindle nut. For adjustment refer to Section 223. Install ONLY identical code, same tolerance class bearings supplied in one package to one wheel hub planetary gear. Adjust the axial play of the axle-shaft t0.4 - 1.6 mm as measured between the sun gear and the friction disk. For adjustment shims of 0.25; 0.5 and 2.0 mm thickness are available. The adjustment is described in the Section 219. WHEEL BRAKE If the brake linings are worn to the permitted limit (max. 7.0 mm as indicated by upper edge of recess on side of the linings) replace the brake linings as specified. Check the brake shoe surface being in contact with the shoe anchor pin and the brake spanner rollers. Adjust the specified shoe clearance (0.3 - 0.6 mm) by the brake lever. After adjustment the brake lining may not interfere with the brake drum. From among the sealing rings of the brake spanners that at the brake spanner head may not pass the surplus lubricant during greasing. The sealing ring at the brake spanner head protects the brake drum against the grease. Make sure to check if the sealing rings are pressed in proper position. True up the brake drum ONLY to the permitted max. 424 mm diameter. DIFFERENTIALS (MAIN DIFFERENTIAL - FORWARD-REAR AND DIFFERENTIAL CARRIER ASSEMBLY - REAR-REAR) Install the taper roller bearings of the drive pinion with preload. Preload should provide that the bearings roll at the torque of 2.5 – 3.5 Nm at forward-rear carrier and at the torque of 2.2 – 2.7 Nm at rear-rear carrier. During inspection the seal ring (4 in figure 1 of Section 310) with the cover (5) are not installed in SECTION 209. GENERAL SERVICE INSTRUCTIONS rear-rear carrier. For adjustment refer to Sections 290 and 317. The gears of the cross differentials should be rotatable without jamming. Install the taper roller bearings of the differentials free of clearance. After adjusting the proper contact pattern and the specified 0.25-0.33 mm backlash, tighten the bearing adjusters on both sides so that they could be fixed by one of the tab lock plates (21). For inspection and adjustment refer to Section 287. At the differential carrier assembly install the taper roller bearings 32212 and 32014 so, to obtain 0.1 to 0.15 mm axial play at the input shaft /68/. For adjustment refer to Section 293. For adjustment of the inter-axle diff. lock actuating pneumatic chamber at the differential carrier assembly refer to Section 294. For adjustment of the cross differential locks refer to the Section 318. GENERAL INSTRUCTIONS For purpose of labor safety during service operations performed on the axle removing the individual assembly units make sure to assure safe backing, fixing or suspension. Install only clean and sound parts free of burr and knock-outs. Before installation wipe the mating surfaces of the parts clean and apply thin coat of oil. For assembly operations use ONLY plastic or copper insert hammer. Before installing the oil seals make sure to check if the sealing lip is sound and apply specified grease to between the sealing lip and the dust protection edge. Install the O-rings also with grease. When installing the taper roller bearings take care of the pairing according to the original packing or to the manufacturer’s specification. The following thread cementing, locking and surface sealing material are used at the axle, e.g.: Thread adhesive: LOCTITE 277 High-strenght Omni FIT 1550 HENKEL Thread locker: LOCTITE 243 Medium-strenght Omni FIT 230 M HENKEL Surface sealant: LOCTITE 515 25
Page 1: WORKSHOP MANUAL REAR AXLES RF17N/H
Page 4 and 5: 4 Removing and Reinstalling the Whe
Page 7 and 8: PREFACE The present document gives
Page 9: This manual has been prepared for o
Page 12 and 13: 205. FEJEZET SECTION 205. SECTION 2
Page 14 and 15: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 16 and 17: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 18 and 19: 206. FEJEZET SECTION 206. MEGHÚZÁ
Page 20 and 21: MEGHÚZÁSI NYOMATÉKOK TORQUE RATI
Page 22 and 23: 207. FEJEZET SECTION 207. BEÁLLÍT
Page 26 and 27: 26 SECTION 210. 210. FEJEZET 210. S
Page 28 and 29: 28 SECTION 212. REMOVING AND REINST
Page 30 and 31: 30 A bolygótartó és a napkerék
Page 32 and 33: 32 A tömít�gy�r� fészkét
Page 34 and 35: REMOVING THE SPINDLE AND THE BRAKE
Page 36 and 37: 260. FEJEZET SECTION 260. A MELLS
Page 38 and 39: A FÉKPOFAGÖRG� ÉS SZERELÉSE 1
Page 40 and 41: A FÉKPOFACSAPPERSELY KI- ÉS BESZE
Page 42 and 43: Nm nyomatékkal húzzuk meg. to 20
Page 44 and 45: Tételei : SECTION 268. Items: AUTO
Page 46 and 47: 46 280. FEJEZET MAIN DIFFERENTIAL S
Page 48 and 49: 48 - 37 - Drive gear - 39 - Hex. fl
Page 50 and 51: 2. ábra: A KAPCSOLÓAGY LEHÚZATÁ
Page 52 and 53: 52 akadás, szorulás, szagatott el
Page 54 and 55: A KERESZTIRÁNYÚ KIEGYENLÍT�M
Page 56 and 57: During drive the rotation should be
Page 58 and 59: elforgatjuk. REASSEMBLING THE DIFFE
Page 60 and 61: SECTION 290. Amennyiben egyezik, ú
Page 62 and 63: REASSEMBLING THE DIFFERENTIAL CARRI
Page 64 and 65: Amennyiben ett�l eltérés mutatk
Page 66 and 67: A tömít�lemezt (101) üssük be
Page 68 and 69: kkal (14) rögzítsük 88,3-108 Nm
Page 70 and 71: 70 A HOSSZIRÁNYÚ KIEGYENLÍT�M
Page 72 and 73: 310. FEJEZEET HAJTÓ ÉS KIEGYENLÍ
Page 74 and 75:
313. FEJEZET Drain the oil from the
Page 76 and 77:
76 A küls� tömít�gy�r�t
Page 78 and 79:
Helyezzük a hajtóm�ház csapág
Page 80 and 81:
TOO DEEP CONTACT If the contact pat
Page 82 and 83:
Apply thin coat of the mating surfa
Page 84 and 85:
317. FEJEZET 120 A csapágyhüvely
Page 86 and 87:
Helyezzük be a csapágyhüvelybe a
Page 88 and 89:
88 Amennyiben a beállítás megfel
Page 90 and 91:
According to the Operators Manual f
Page 92:
Initial Failure Reporting 92 WARRAN
show all

workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?