workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

More documents

Recommendations

Info

Tételei : SECTION 268. Items: AUTOMATIC SLACK ADJUSTER The 1 - Állítólap slack adjuster is automatically readjusted according Adjusting to the plate brake lining wear. In 2 - case Rögzít�csavar of replacing (Lt. the 13) brake linings or after repairing the Setscrew axle perform (Hex. adjustment distance 13) of the shoe clearance and the automatic slack adjuster as follows: 3 - Rögzít�csavar (Lt. 10) Items: Setscrew (Hex. distance 10) 1 - Adjusting plate 2 4 - Setscrew Véd�sapka (Hex. distance 13) 3 - Setscrew Protection (Hex. distance 10) 4 - Protection 5 - Hex. Hatlapú adjusting állítógy�r� ring (Hex. (Lt. 32) distance 32) 6 - Stop Hex. pin adjusting ring (Hex. distance 32) 7 - Plastic thread protector 6 - Ütköz�csap 8 - Toothed disk Stop pin 7 - M�anyag menetvéd� I. Position Plastic of thread wear protector indicator disk a new brake lining. II. 8 - Position Fogazott of tárcsa wear indicator disk at worn brake Toothed lining. disk Brake drum diameter: 420 mm. Adjustment data: A= Distance between the chamber holder plane and the brake lever bore C =Brake lever installation radius For dimension A -C refer to “TECHNICAL DATA”. I. A kopásjelz� tárcsa helyzete új fékbetét estén. Adjusting position of the brake lever and the shoe clearance: II. A kopásjelz� tárcsa helyzete lekopott fékbetét - esetén. Remove Fékdobátmér� setscrew (2, =420 3). mm. - Take care of the plastic thread protector (7). - Remove the adjusting plate (1) and the plastic protection cap (4). - By turning the hex. adjusting ring (5) to proper direction adjust the specified distance between the seating surface and the brake lever bore. (Start adjustment from a distance higher than specified. If required, also adjust the push rod clevis.) - After the above operation adjust the shoe clearance to 0.3 - 0.6 mm. Adjusting and fixing the adjusting plate: Secure the fork “E” of the adjusting plate (1) in bottom position relative to stop pin (6) as shown in Fig. 1. 44 Fig. 1.: AUTOMATIC SLACK ADJUSTER 684.10-5 1. ábra: AUTOMATIKUS UTÁNÁLLÍTÁSÚ FÉKKAR Fig. 1.: AUTOMATIC SLACK ADJUSTER I. Position of wear indicator disk a new brake lining. Complete adjustment by reinstalling the plastic protection II. Position cap (4) of and wear the indicator adjusting disk plate at (1) worn as brake well as lining. installing Brake and drum securing diameter: the 420 setscrew mm. (2, 3) and screwing on the plastic thread protector. During fixing plane of the adjusting plate should be perpendicular to the stop pin (6). 67 Before installation apply graphitic grease to serration of the brake lever.
Main Differential (RF17) 45
Page 1: WORKSHOP MANUAL REAR AXLES RF17N/H
Page 4 and 5: 4 Removing and Reinstalling the Whe
Page 7 and 8: PREFACE The present document gives
Page 9: This manual has been prepared for o
Page 12 and 13: 205. FEJEZET SECTION 205. SECTION 2
Page 14 and 15: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 16 and 17: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 18 and 19: 206. FEJEZET SECTION 206. MEGHÚZÁ
Page 20 and 21: MEGHÚZÁSI NYOMATÉKOK TORQUE RATI
Page 22 and 23: 207. FEJEZET SECTION 207. BEÁLLÍT
Page 24 and 25: LEHÚZATÓ- ÉS VEZET� CSAVAROK P
Page 26 and 27: 26 SECTION 210. 210. FEJEZET 210. S
Page 28 and 29: 28 SECTION 212. REMOVING AND REINST
Page 30 and 31: 30 A bolygótartó és a napkerék
Page 32 and 33: 32 A tömít�gy�r� fészkét
Page 34 and 35: REMOVING THE SPINDLE AND THE BRAKE
Page 36 and 37: 260. FEJEZET SECTION 260. A MELLS
Page 38 and 39: A FÉKPOFAGÖRG� ÉS SZERELÉSE 1
Page 40 and 41: A FÉKPOFACSAPPERSELY KI- ÉS BESZE
Page 42 and 43: Nm nyomatékkal húzzuk meg. to 20
Page 46 and 47: 46 280. FEJEZET MAIN DIFFERENTIAL S
Page 48 and 49: 48 - 37 - Drive gear - 39 - Hex. fl
Page 50 and 51: 2. ábra: A KAPCSOLÓAGY LEHÚZATÁ
Page 52 and 53: 52 akadás, szorulás, szagatott el
Page 54 and 55: A KERESZTIRÁNYÚ KIEGYENLÍT�M
Page 56 and 57: During drive the rotation should be
Page 58 and 59: elforgatjuk. REASSEMBLING THE DIFFE
Page 60 and 61: SECTION 290. Amennyiben egyezik, ú
Page 62 and 63: REASSEMBLING THE DIFFERENTIAL CARRI
Page 64 and 65: Amennyiben ett�l eltérés mutatk
Page 66 and 67: A tömít�lemezt (101) üssük be
Page 68 and 69: kkal (14) rögzítsük 88,3-108 Nm
Page 70 and 71: 70 A HOSSZIRÁNYÚ KIEGYENLÍT�M
Page 72 and 73: 310. FEJEZEET HAJTÓ ÉS KIEGYENLÍ
Page 74 and 75: 313. FEJEZET Drain the oil from the
Page 76 and 77: 76 A küls� tömít�gy�r�t
Page 78 and 79: Helyezzük a hajtóm�ház csapág
Page 80 and 81: TOO DEEP CONTACT If the contact pat
Page 82 and 83: Apply thin coat of the mating surfa
Page 84 and 85: 317. FEJEZET 120 A csapágyhüvely
Page 86 and 87: Helyezzük be a csapágyhüvelybe a
Page 88 and 89: 88 Amennyiben a beállítás megfel
Page 90 and 91: According to the Operators Manual f
Page 92: Initial Failure Reporting 92 WARRAN

workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?