workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

More documents

Recommendations

Info

REMOVING THE SPINDLE AND THE BRAKE SUPPORT ASSY. After removing the wheel hub back out the hax. bolts (41) attaching the spindle (33) to flange of the axle housing (42) and pull the spindle out of the axle housing bore 34 SECTION 226. REMOVING AND REINSTALLING THE SPINDLE AND THE BRAKE SUPPORT ASSY. 229. FEJEZET SECTION 229. A BLOKKOLÁSGÁTLÓ SZERKEZETI ELEMEINEK BEÉPÍTÉSI EL�ÍRÁSAI REINSTALLING THE SPINDLE AND THE BRAKE SUPPORT ASSY. Aligning the bores push the spindle supplied together with the brake support into the axle housing bore. Secure the spindle by hex. bolts applied with thread locker and tighten the bolts to 360 - 380 Nm torque. SECTION 229. INSTALLATION INSTRUCTIONS FOR MOUNTING THE PARTS OF THE ANTI- BLOCKING SYSTEM INSTALLATION INSTRUCTIONS FOR MOUNTING THE PARTS OF THE ANTIBLOCKING SYSTEM Ez a leírás a futóm�be a vev� által utólagosan This description contains the constructional elements This description contains the constructional beépíthet� blokkolásgátló elements (ABS) During és kipörgésgátló operation of the the distance antiblocking between and anti-skid the systems speed (ABS and of the antiblocking and anti-skid (ASR) systems szerkezeti (ABS elemeit and és azok sensor beépítési and el�írásait the inductor ASR), that ring can should be installed be by 0,8 the mm customer max. into the tartalmazza. ASR), that can be installed by the customer into the Lead the wire of speed axle as well sensor as the installation from the instructions. axle brake axle as well as the installation instructions. A "M�SZAKI ADATOK" system cím� kiadványban in such a way In the that „TECHNICAL the radius DATA” of the <strong>manual</strong> blended items In the „TECHNICAL DATA” <strong>manual</strong> meghatározott items típusok identified tartalmazzák wire azokat never a tételeket less than identified a minimum as (A, C) are of necessary R50 mm to mount and fix the ABS as (A, C) are necessary to mount (A), the amelyek ABS and az ASR ABS és the ASR wire tételek at 50 (1) mm and intervals ASR items while (1). inside the hot brake beépítéséhez szükségesek. items (1). system . 1. A BEÉPÍTHET� BLOKKOLÁSGÁTLÓ (ABS) 1. INSTALLABLE ELEMENTS OF THE ANTI- 1. INSTALLABLE ELEMENTS OF THE ANTI-BLOCK Check the runout of toothed impulse inducing ring. Al- ÉS KIPÖRGÉSGÁTLÓ (ASR) TÉTELEK BLOCK- AND ANTI-SKID SYSTEMS AND ANTI-SKID SYSTEMS lowable runout of the ring teeth in the direction of the 1.1 Fordulatszám-érzékel�: speed sensor is 0,2 1.1 mm Revolution max. sensor: 1.1 Revolution sensor: Robert Bosch GmbH A 335 545 231 vagy Robert Bosch GmbH A 335 545 231 or Robert Bosch GmbH A 335 545 KNORR-BREMSE 231 or ZB 9010-I/83315 vagy KNORR-BREMSE ZB 9010-I/83315 or KNORR-BREMSE ZB 9010-I/83315 WABCO or441 032 001 0 vagy WABCO 441 032 001 0 or WABCO 441 032 808 0 vagy WABCO 441 032 808 0 or WABCO 441 032 001 0 or WABCO 441 032 578 0 WABCO 441 032 578 0 WABCO 441 032 808 0 or Note: Tachometer to be built in only with spring bush- WABCO 441 032 578 0 1.2 Rugós persely: ing of the same 1.2 manufacturing. Spring bushing: Besides BOSCH, Robert Bosch GmbH C 335 002 431 A vagy Robert Bosch GmbH C 335 002 431 A or 1.2 Spring bushing: KNORR-BREMSE 4B 69698 vagy KNORR and WABCO KNORR-BREMSE tachometer, 4B a 69698 tachometer or of Robert Bosch GmbH C 335 002 WABCO 431 A 899 or 760 510 4 vagy other production, interchangeable WABCO 899 760 510 with 4 or the above is WABCO 899 759 815 4 allowed to be built in. WABCO If the 899 impulse 759 815 ring 4 KNORR-BREMSE 4B 69698 or is changed, WABCO 899 760 510 4 or before pressing the new impulse ring is to be heat- WABCO 899 759 815 4 MEGJEGYZÉS : A fordulatszámérzékel� ed uniformly csak to 150°C NOTE: and Install pushed speed sensor up to with stop the same on the type of azonos gyártású rugós persellyel wheel együtt építhet� hub. be. springed bush only. NOTE: Install speed sensor with the same type of springed bush only. A - Fogazott impulzusgerjeszt� gy�r� A - Toothed impulse ring. A - Toothed impulse ring. A 1.1 1.2 2. MOUNTING INSTRUCTIONS Apply copper paste or silicon grease (e.g. Molykote FP186, NBU 30 PTM Univew N3) to the Ø18H11 bore of the speed sensor holder before installation of the springed bush, to prevent corrosion. Push the springed bush into the Ø18H11 bore from the middle of axle to mate (12). Insert speed sensor (1.1) into the spring bush, and push towards the inductor ring on the wheel hub. After dismounting wheel hub this adjustment must be made every time. 52 939.93-3 1. ábra : A blokkolásgátló beépítése Fig. 1.: MOUNTING THE ANTI-LOCKING SYSTEM Fig. 1.: Mounting the Anti-locking system.
WHEEL BRAKE 35
Page 1: WORKSHOP MANUAL REAR AXLES RF17N/H
Page 4 and 5: 4 Removing and Reinstalling the Whe
Page 7 and 8: PREFACE The present document gives
Page 9: This manual has been prepared for o
Page 12 and 13: 205. FEJEZET SECTION 205. SECTION 2
Page 14 and 15: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 16 and 17: M�SZAKI ADATOK TECHNICAL DATA MEG
Page 18 and 19: 206. FEJEZET SECTION 206. MEGHÚZÁ
Page 20 and 21: MEGHÚZÁSI NYOMATÉKOK TORQUE RATI
Page 22 and 23: 207. FEJEZET SECTION 207. BEÁLLÍT
Page 24 and 25: LEHÚZATÓ- ÉS VEZET� CSAVAROK P
Page 26 and 27: 26 SECTION 210. 210. FEJEZET 210. S
Page 28 and 29: 28 SECTION 212. REMOVING AND REINST
Page 30 and 31: 30 A bolygótartó és a napkerék
Page 32 and 33: 32 A tömít�gy�r� fészkét
Page 36 and 37: 260. FEJEZET SECTION 260. A MELLS
Page 38 and 39: A FÉKPOFAGÖRG� ÉS SZERELÉSE 1
Page 40 and 41: A FÉKPOFACSAPPERSELY KI- ÉS BESZE
Page 42 and 43: Nm nyomatékkal húzzuk meg. to 20
Page 44 and 45: Tételei : SECTION 268. Items: AUTO
Page 46 and 47: 46 280. FEJEZET MAIN DIFFERENTIAL S
Page 48 and 49: 48 - 37 - Drive gear - 39 - Hex. fl
Page 50 and 51: 2. ábra: A KAPCSOLÓAGY LEHÚZATÁ
Page 52 and 53: 52 akadás, szorulás, szagatott el
Page 54 and 55: A KERESZTIRÁNYÚ KIEGYENLÍT�M
Page 56 and 57: During drive the rotation should be
Page 58 and 59: elforgatjuk. REASSEMBLING THE DIFFE
Page 60 and 61: SECTION 290. Amennyiben egyezik, ú
Page 62 and 63: REASSEMBLING THE DIFFERENTIAL CARRI
Page 64 and 65: Amennyiben ett�l eltérés mutatk
Page 66 and 67: A tömít�lemezt (101) üssük be
Page 68 and 69: kkal (14) rögzítsük 88,3-108 Nm
Page 70 and 71: 70 A HOSSZIRÁNYÚ KIEGYENLÍT�M
Page 72 and 73: 310. FEJEZEET HAJTÓ ÉS KIEGYENLÍ
Page 74 and 75: 313. FEJEZET Drain the oil from the
Page 76 and 77: 76 A küls� tömít�gy�r�t
Page 78 and 79: Helyezzük a hajtóm�ház csapág
Page 80 and 81: TOO DEEP CONTACT If the contact pat
Page 82 and 83: Apply thin coat of the mating surfa
Page 84 and 85:
317. FEJEZET 120 A csapágyhüvely
Page 86 and 87:
Helyezzük be a csapágyhüvelybe a
Page 88 and 89:
88 Amennyiben a beállítás megfel
Page 90 and 91:
According to the Operators Manual f
Page 92:
Initial Failure Reporting 92 WARRAN
show all

workshop manual rear axles rf17n/h r17n/h - Marmon-Herrington

Create successful ePaper yourself

Delete template?

Save as template?