AS9N010B.STB AS-93plus Service Manual.fm - LIQUID-scan GmbH ...

More documents

Recommendations

Info

Communication The Communication dialog allows to set up the communication type and parameters for the communication of the Utilities program with the autosampler. The communication type/parameters have to match with the dip-switch settings of the autosampler. If the communication parameters are not correct, you will not be able to download any of the utilities. To change the communication parameters: 1. In the Communication dialog: 1. Select the required Communication Interface: Click on IEEE or RS232. 2. If you select IEEE, enter the IEEE Address for the autosampler. –or– If you select RS232, select the communication port (COM port) for the autosampler. The settings are implemented as soon as you change to a different page or close the window. Figure 18 AS-93 Utilities: Communication Dialog 44 of 68 AS9N010B.STB
Tray Download A tray definition file provides the system with information about the group of sample racks installed on the autosampler. This information includes the coordinates of each location in the sample rack. The system requires this information to move the sampling probe to the correct location for each sample container in the rack. Refer to page 48 for further information about location coordinates. The spectrometer operating software already provides tray definition files for the Perkin Elmer sample tray type E, F and G. Tray definition files for each of the sample tray types that can be selected are also provided with the autosampler. The most recent software versions of the AA Winlab software such as Rev.3.00 or higher (used to control the AAnalyst 100/300), Rev.3.90 or higher (used to control the AAnalyst 600/700/800), the 32 bit ICP WinLab software and the ICP-MS ELAN software make direct use of tray definition files. In this case the tray definition file must be located in the WinLab/Elan directory, i.e. a tray download by means of the AS-93 Utility software is NOT required. A tray download as described below is only required in the case, that the AS-93plus is controlled by software versions not supporting tray definition files, e.g. 16 bit ICP WinLab software or AA WinLab software Rev. 2.61. Note Tray definition files for the use with AA WinLab software and ICP-MS ELAN software are available from the AS-93 Utility disk P/N B314-0758 Setting up tray definition files If you change the types of sample racks for use (e.g. you want to use Gilson racks instead of PerkinElmer racks), you must set up the tray definition files for those sample racks. In the spectrometer operating software you can select tray type E, F, or G. The Tray Download dialog allows to define which tray definition files are assigned to E, F and to G. Note Any change of the rack configuration assigned to a tray type requires a download of the correct tray definition files. Performing a tray download Performing a tray download 1. Make sure that the communication parameters have been set correctly. 1. In the Tray File dialog click on Open for Tray E. 2. In the Open window, in Look in ..., select the directory containing the tray definition files, click on the file (group of sample racks) that you wish to assign to Tray E and then click on Open. 3. Repeat this procedure for Tray F and Tray G, if required. Note: You can assign one, two, or three tray definition files. It is not necessary to always assign three. 2. In the Tray File dialog, click on Download to implement the tray definition files in the spectrometer’s operating software. AS9N010B.STB 45 of 68
Page 1 and 2: AA Business Unit Service Informatio
Page 3 and 4: Configuration 1 . . . . . . . . . .
Page 5 and 6: Key benefits: • fast, accurate ra
Page 7 and 8: Tray group F This group (provided a
Page 9 and 10: Technical data System design Compac
Page 11 and 12: Checklist of the AS-93plus Accessor
Page 13 and 14: Assembling sample racks For easy sh
Page 15 and 16: Diluter (option) Autosampler Figure
Page 17 and 18: The usual addresses preselected for
Page 19 and 20: Caution: Risk of damage to the auto
Page 21 and 22: Connecting the sample tube The samp
Page 23 and 24: Alternate connection procedure: Ada
Page 25 and 26: 6. Install the sample racks on the
Page 27 and 28: Sample tray group G Rinsing port 0
Page 29 and 30: Sample tray groups for Gilson racks
Page 31 and 32: Tubing configurations You can set u
Page 33 and 34: Connecting the tubes for configurat
Page 39 and 40: Installing the rinsing port Lug pas
Page 41 and 42: 7. Click on "Next" to finish the re
Page 43: AS-93plus Utilities The AS-93 utili
Page 47 and 48: How to create a tray definition fil
Page 49 and 50: Rinse Download This utility enables
Page 51 and 52: Information The Information window
Page 53 and 54: 1. Carefully turn over the autosamp
Page 55 and 56: If you are using another sample tra
Page 57 and 58: 1. Switch of the AS-93 by unpluggin
Page 59 and 60: 3. Click on the function key "Get X
Page 61 and 62: Checking the Event Relay The Event
Page 63 and 64: Maintenance There are not much part
Page 65 and 66: Pump Commands • stop control.pump
Page 67 and 68: AS-93plus Error Code Reference Tabl

AS9N010B.STB AS-93plus Service Manual.fm - LIQUID-scan GmbH ...

Create successful ePaper yourself

Delete template?

Save as template?