AFS Foundry Sand Testing Equipment Operating Instructions Manual

More documents

Recommendations

Info

RIDSDALE TRANSVERSE CORE STRENGTH ACCESSORYFOR HIGH STRENGTH TESTING MACHINEIINSTALLATION(a)(b)(c)(d)Press one of the “direction of travel” buttons on the cypher to obtain sufficientclearance to insert the transverse core strength accessory.Ensure the socket head screws on the support arm carriers are loosened (using thekey provided) enabling the two parts of the accessory to swivel.Screw in the large support arm carrier of the accessory into the load cell (a) atapproximately 45° ensuring that the sample support pin is located at the bottom ofthe arm. Locate the other half of the accessory into the traversing ram (b).Line up each half of the accessory using the locating pins and tighten up the sockethead screws on the support arm carriers (ensuring the accessory does not touch orfoul any part of the machine) and then remove locating pins.IITEST PROCEDURE(a)(b)(c)Using one of the “direction of travel” buttons on the cypher, adjust the distancebetween the support arm carriers to accommodate a transverse sand specimenallowing approximately 1/16 inch (1.5 mm) clearance.Place the specimen between the knife edges, replace the perspex safety cover.Before commencement of the test ensure that the cursor is displayed on the left handbottom corner of the cypher display. To adjust the cursor, repeatedly press the“max/min” button.109
RIDSDALE TRANSVERSE CORE STRENGTH ACCESSORYFOR HIGH STRENGTH TESTING MACHINE (cont’d)IITEST PROCEDURE (cont’d)(d)(e)(f)(g)(h)for tranverse testing select “Mode 3” button on the cypher.Zero the display on the ipher using the “reset” and “zero” buttons.To test, press one of the “direction of travel” buttons. (If using software package,press F4 simultaneously).Once the specimen has broken, press the “stop” button and remove the remains ofthe previous test piece.Repeat from Procedure (a) to carry out further tests.110
Page 1 and 2:
FOUNDRYSANDTESTINGEQUIPMENTOPERATIN
Page 4 and 5:
RIDSDALE SILICA SAND SAMPLER(for ex
Page 6 and 7:
RIDSDALE-DIETERTRAPID SAND WASHER (
Page 9 and 10:
RIDSDALE-DIETERTMETHYLENE BLUE CLAY
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
INSTRUCTIONS FOR THE CORRECT USE OF
Page 19 and 20:
RIDSDALE-DIETERTSAND SPECIFIC SURFA
Page 21 and 22:
Page 23 and 24:
TABLE IISCREEN ANALYSISBS 410: 1986
Page 25 and 26:
Page 27 and 28:
RIDSDALE LABORATORY MILLIGENERAL PR
Page 29 and 30:
RIDSDALE LABORATORY MILL (cont’d)
Page 31 and 32:
RIDSDALE LABORATORY SAND MIXER (con
Page 33 and 34:
RIDSDALE-DIETERT MOISTURE TELLER (c
Page 35 and 36:
RIDSDALE-DIETERT MOISTURE TELLER (c
Page 37 and 38:
RIDSDALE MOISTBALANCE (cont’d)IVT
Page 39 and 40:
RIDSDALE DIGITAL BALANCEOPERATIONAC
Page 41 and 42:
RIDSDALE-DIETERT (AFS)LABORATORY SA
Page 43 and 44:
RIDSDALE-DIETERT(AFS) LABORATORY SA
Page 45 and 46:
RIDSDALE-DIETERT DENSITY INDICATOR
Page 47 and 48:
RIDSDALE-DIETERT FLOWABILITY INDICA
Page 49 and 50:
RIDSDALE-DIETERT COMPACTABILITY TES
Page 51 and 52:
RIDSDALE-DIETERTTENSILE RAMMING ACC
Page 53 and 54:
RIDSDALE-DIETERTTRANSVERSE RAMMING
Page 55 and 56:
RIDSDALE-DIETERT SPLIT SPECIMEN TUB
Page 57 and 58:
RIDSDALE CO 2 GASSING ACCESSORIES (
Page 59 and 60:
RIDSDALE LABORATORY CORE-BAKING OVE
Page 61 and 62: RIDSDALE LABORATORY CORE-BAKING OVE
Page 63 and 64: RIDSDALE LABORATORY CORE TEST PIECE
Page 65 and 66: RIDSDALE LABORATORY CORE TEST PIECE
Page 67 and 68: RIDSDALE-DIETERT PERMEABILITY METER
Page 69 and 70: RIDSDALE-DIETERT PERMEABILITY METER
Page 71 and 72: 68RIDSDALE-DIETERT PERMEABILITY MET
Page 73 and 74: RIDSDALE-DIETERT ELECTRIC PERMMETER
Page 75 and 76: RIDSDALE-DIETERT MOULD PERMEABILITY
Page 77 and 78: CORE PERMEABILITY TUBEIGENERAL PRIN
Page 79 and 80: BASE PERMEABILITY SCREENSThe base p
Page 81 and 82: RIDSDALE SHATTER INDEX TESTER (AFS)
Page 83 and 84: RIDSDALE-DIETERTGREEN COMPRESSION S
Page 85 and 86: RIDSDALE-DIETERTHAND OPERATED UNIVE
Page 87 and 88: RIDSDALE-DIETERTHAND OPERATED UNIVE
Page 89 and 90: RIDSDALE-DIETERTMOTOR DRIVEN UNIVER
Page 95 and 96: RIDSDALE-DIETERTHIGH DRY STRENGTH A
Page 97 and 98: RIDSDALE-DIETERTTENSILE CORE STRENG
Page 99 and 100: RIDSDALE-DIETERTTRANSVERSE CORE STR
Page 101 and 102: RIDSDALE-DIETERTTRANSVERSE SHELL ST
Page 103 and 104: RIDSDALE-DIETERTSHELL MOULD TRANSVE
Page 105 and 106: RIDSDALE-DIETERTSHELL MOULD TENSILE
Page 107 and 108: RIDSDALE SPLITTING STRENGTH ACCESSO
Page 109 and 110: RIDSDALE COMPRESSION STRENGTH ACCES
Page 111: RIDSDALE TENSILE CORE STRENGTH ACCE
Page 115 and 116: RIDSDALE PEEL-BACK TESTER (cont’d
Page 117 and 118: RIDSDALE CALIBRATION EQUIPMENTTUBE
Page 119 and 120: RIDSDALE GAS DETERMINATOR (cont’d
Page 125 and 126: RIDSDALE-DIETERTGREEN HARDNESS TEST
Page 127 and 128: RIDSDALE-DIETERTGREEN HARDNESS TEST
Page 129 and 130: RIDSDALE-DIETERTCORE HARDNESS TESTE
Page 131 and 132: RIDSDALE IMPACT PENETRATION TESTER
Page 133 and 134: RIDSDALE-DIETERTMOULD STRENGTH TEST
Page 135: RIDSDALE-DIETERTFOUNDRY HYDROMETER
show all

AFS Foundry Sand Testing Equipment Operating Instructions Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?