LTQ Orbitrap XL Hardware Manual

More documents

Recommendations

Info

Read This First Safety and EMC Information Safety and Special Notices Note Read and understand the various precautionary notes, signs, and symbols contained inside this manual pertaining to the safe use and operation of this product before using the device. ▲ Make sure you follow the precautionary statements presented in this guide. The safety and other special notices appear different from the main flow of text. Safety and special notices include the following: Warning Warnings highlight hazards to human beings. Each Warning is accompanied by a Warning symbol. ▲ Caution Cautions highlight information necessary to protect your instrument from damage. ▲ Note Notes highlight information that can affect the quality of your data. In addition, notes often contain information that you might need if you are having trouble. ▲ vi LTQ Orbitrap XL Hardware Manual Thermo Fisher Scientific
Identifying Safety Information General Safety Precautions Read This First Safety and EMC Information The LTQ Orbitrap XL Hardware Manual contains precautionary statements that can prevent personal injury, instrument damage, and loss of data if properly followed. Warning symbols alert the user to check for hazardous conditions. These appear throughout the manual, where applicable. The most common warning symbols are: Warning This general symbol indicates that a hazard is present that could result in injuries if it is not avoided. The source of danger is described in the accompanying text. ▲ Warning High Voltages capable of causing personal injury are used in the instrument. The instrument must be shut down and disconnected from line power before service is performed. Do not operate the instrument with the top cover off. Do not remove protective covers from PCBs. ▲ Warning Treat heated zones with respect. Parts of the instrument might be very hot and might cause severe burns if touched. Allow hot components to cool before servicing them. ▲ Warning Wear gloves when handling toxic, carcinogenic, mutagenic, or corrosive/irritant chemicals. Use approved containers and procedures for disposal of waste solution. ▲ In addition to the above described, every instrument has specific hazards. So, be sure to read and comply with the precautions described in the subsequent chapters of this guide. They will help ensure the safe, long-term use of your system. Observe the following safety precautions when you operate or perform service on your instrument: • Before plugging in any of the instrument modules or turning on the power, always make sure that the voltage and fuses are set appropriately for your local line voltage. • Only use fuses of the type and current rating specified. Do not use repaired fuses and do not short-circuit the fuse holder. Thermo Fisher Scientific LTQ Orbitrap XL Hardware Manual vii
Page 1 and 2: For Research Use Only Not for use i
Page 3: Place Declaration of Conformity her
Page 6 and 7: Conformité DEEE Ce produit doit ê
Page 8 and 9: Read This First Related Documentati
Page 10 and 11: Read This First Typographical Conve
Page 14 and 15: Read This First Safety and EMC Info
Page 17 and 18: Contents Chapter 1 Functional Descr
Page 19 and 20: Figures LTQ Orbitrap XL front view
Page 21: Tables System status LEDs of the Pr
Page 24 and 25: Functional Description General Desc
Page 26 and 27: Functional Description General Desc
Page 28 and 29: Functional Description Control Elem
Page 34 and 35: Functional Description Linear Ion T
Page 36 and 37: Functional Description Orbitrap Ana
Page 42 and 43: Functional Description Vacuum Syste
Page 48 and 49: Functional Description Gas Supply I
Page 50 and 51: Functional Description Cooling Wate
Page 52 and 53: Functional Description Printed Circ
Page 62 and 63:
Functional Description Printed Circ
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 79 and 80:
Chapter 2 Basic System Operations M
Page 81 and 82:
Basic System Operations Shutting Do
Page 83 and 84:
Shutting Down the System Basic Syst
Page 85 and 86:
Starting Up the System after a Shut
Page 87 and 88:
Basic System Operations Starting Up
Page 89:
Basic System Operations Resetting t
Page 92 and 93:
User Maintenance General Remarks Ge
Page 94 and 95:
User Maintenance Baking Out the Sys
Page 96 and 97:
User Maintenance Maintaining the Va
Page 99 and 100:
Chapter 4 Replaceable Parts This ch
Page 101 and 102:
Parts Orbitrap Analyzer Parts Pumpi
Page 103 and 104:
Parts Gas and Water Supply Replacea
Page 105 and 106:
Electronic Parts Electronics - Righ
Page 107:
Electronics Main Supply Table 4-18.
Page 110 and 111:
Glossary: collision-induced dissoci
Page 112 and 113:
Glossary: IEEE IEEE Institute of El
Page 114 and 115:
Glossary: P/N P/N part number p-p p
Page 116 and 117:
Glossary: V dc V dc volts direct cu
Page 118 and 119:
Index: D control unit, for turbopum
Page 120 and 121:
Index: O O pressure 1-26 pressure r
Page 122:
Index: W quality 1-40 safety thresh
show all

LTQ Orbitrap XL Hardware Manual

Create successful ePaper yourself

Delete template?

Save as template?