LTQ Orbitrap XL Hardware Manual

More documents

Recommendations

Info

Basic System Operations Resetting the System Resetting the System If communication between the LTQ Orbitrap XL and data system computer is lost, it may be necessary to reset the system using the Reset button of the LTQ XL. The procedure given here assumes that the LTQ Orbitrap XL and data system computer are both powered on and are operational. If the instrument, data system computer, or both are off, refer to topic “Starting Up the System after a Shutdown” on page 2-7. To reset the LTQ Orbitrap XL, press the Reset button of the linear ion trap. See the LTQ XL Hardware Manual for the location of the Reset button. When you press the Reset button, the following occurs: 1. An interrupt on the mainboard of the internal computer causes the internal computer to reboot. All LEDs on the front panel are off except the Power LED. 2. After several seconds, the Communication LED is illuminated yellow to indicate that the data system and the instrument are starting to establish a communication link. 3. After several more seconds, the Communication LED is illuminated green to indicate that the data system and the instrument have established a communication link. Software for the operation of the instrument is then transferred from the data system to the instrument. 4. After 3 min, the software transfer is complete. The System LED is illuminated either green to indicate that the instrument is functional and the high voltages are on, or yellow to indicate that the instrument is functional and it is in Standby condition. 2-10 LTQ Orbitrap XL Hardware Manual Thermo Fisher Scientific
Basic System Operations Resetting the Tune and Calibration Parameters to their Default Values Resetting the Tune and Calibration Parameters to their Default Values You can reset the LTQ Orbitrap XL system tune and calibration parameters to their default values at any time. This feature may be useful if you have manually set some parameters that have resulted in less than optimum performance. To reset the LTQ Orbitrap XL tune and calibration parameters to their default values, proceed as follows: In the Tune Plus window, • Choose File > Restore Factory Calibration to restore the default calibration parameters, or • Choose File > Restore Factory Tune Method to restore the default tune parameters. Note Make sure that any problems you might be experiencing are not due to improper API source settings (spray voltage, sheath and auxiliary gas flow, ion transfer capillary temperature, etc.) before resetting the system parameters to their default values. ▲ Thermo Fisher Scientific LTQ Orbitrap XL Hardware Manual 2-11
Page 1 and 2:
For Research Use Only Not for use i
Page 3:
Place Declaration of Conformity her
Page 6 and 7:
Conformité DEEE Ce produit doit ê
Page 8 and 9:
Read This First Related Documentati
Page 10 and 11:
Read This First Typographical Conve
Page 12 and 13:
Read This First Safety and EMC Info
Page 14 and 15:
Read This First Safety and EMC Info
Page 17 and 18:
Contents Chapter 1 Functional Descr
Page 19 and 20:
Figures LTQ Orbitrap XL front view
Page 21:
Tables System status LEDs of the Pr
Page 24 and 25:
Functional Description General Desc
Page 26 and 27:
Functional Description General Desc
Page 28 and 29:
Functional Description Control Elem
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Functional Description Linear Ion T
Page 36 and 37:
Functional Description Orbitrap Ana
Page 38 and 39: Functional Description Orbitrap Ana
Page 40 and 41: Functional Description Orbitrap Ana
Page 42 and 43: Functional Description Vacuum Syste
Page 48 and 49: Functional Description Gas Supply I
Page 50 and 51: Functional Description Cooling Wate
Page 52 and 53: Functional Description Printed Circ
Page 79 and 80: Chapter 2 Basic System Operations M
Page 81 and 82: Basic System Operations Shutting Do
Page 83 and 84: Shutting Down the System Basic Syst
Page 85 and 86: Starting Up the System after a Shut
Page 87: Basic System Operations Starting Up
Page 92 and 93: User Maintenance General Remarks Ge
Page 94 and 95: User Maintenance Baking Out the Sys
Page 96 and 97: User Maintenance Maintaining the Va
Page 99 and 100: Chapter 4 Replaceable Parts This ch
Page 101 and 102: Parts Orbitrap Analyzer Parts Pumpi
Page 103 and 104: Parts Gas and Water Supply Replacea
Page 105 and 106: Electronic Parts Electronics - Righ
Page 107: Electronics Main Supply Table 4-18.
Page 110 and 111: Glossary: collision-induced dissoci
Page 112 and 113: Glossary: IEEE IEEE Institute of El
Page 114 and 115: Glossary: P/N P/N part number p-p p
Page 116 and 117: Glossary: V dc V dc volts direct cu
Page 118 and 119: Index: D control unit, for turbopum
Page 120 and 121: Index: O O pressure 1-26 pressure r
Page 122: Index: W quality 1-40 safety thresh
show all

LTQ Orbitrap XL Hardware Manual

Create successful ePaper yourself

Delete template?

Save as template?