LTQ Orbitrap XL Hardware Manual

More documents

Recommendations

Info

User Maintenance Maintaining the Vacuum System Maintaining the Vacuum System Exchanging the Lubricant Reservoir of the Turbopumps The turbopumps 1 need maintenance work that is briefly outlined below. Note The manuals of the pump manufacturers give detailed advice regarding safety, operation, maintenance, and installation. Please note the warnings and precautions contained in these manuals! ▲ Note For all manipulations at the pumps, note the advice, warnings, and cautions contained in the pump manuals! ▲ For the turbopumps, we recommend exchanging the lubricant reservoir in a one-year cycle. At each exchange procedure, the complete lubricant reservoir must be exchanged! Note The storage stability of the lubrication oil is limited. The specification of durability is given by the pump manufacturer. (Refer to the manuals for the turbopumps.) ▲ Replacements for the turbopump lubricant reservoirs (TMH 071 P: P/N 017 2350; TMU 262: P/N 105 0160) are available from Thermo Fisher Scientific. The disposal of used oil is subject to the relevant regulations. 1For maintenance of the forepumps, refer to the LTQ XL Hardware Manual or the pump manufacturer’s manual. 3-6 LTQ Orbitrap XL Hardware Manual Thermo Fisher Scientific
Maintenance of the Recirculating Chiller Reservoir Fluid Bag Filter Condenser Filter User Maintenance Maintenance of the Recirculating Chiller For the NESLAB ThermoFlex 900 recirculating chiller, the following checks should be carried out on a regular basis. Note For further information and maintenance instructions, refer to the manufacturer’s manual supplied with the instrument. ▲ Periodically inspect the fluid inside the reservoir. If cleaning is necessary, flush the reservoir with a cleaning fluid compatible with the circulating system and the cooling fluid. The cooling fluid should be replaced periodically. Replacement frequency depends on the operating environment and amount of usage. Warning Before changing the operating fluid make sure it is at safe handling temperature. ▲ The ThermoFlex 900 recirculating chiller installed in the cooling circuit of the instrument is equipped with a fluid bag filter, which needs to be replaced on a regular basis. Replacement bags are available from Thermo Fisher Scientific. To prevent a loss of cooling capacity and a premature failure of the cooling system, clean the condenser filter regularly. If necessary, replace it. Thermo Fisher Scientific LTQ Orbitrap XL Hardware Manual 3-7
Page 1 and 2:
For Research Use Only Not for use i
Page 3:
Place Declaration of Conformity her
Page 6 and 7:
Conformité DEEE Ce produit doit ê
Page 8 and 9:
Read This First Related Documentati
Page 10 and 11:
Read This First Typographical Conve
Page 12 and 13:
Read This First Safety and EMC Info
Page 14 and 15:
Read This First Safety and EMC Info
Page 17 and 18:
Contents Chapter 1 Functional Descr
Page 19 and 20:
Figures LTQ Orbitrap XL front view
Page 21:
Tables System status LEDs of the Pr
Page 24 and 25:
Functional Description General Desc
Page 26 and 27:
Functional Description General Desc
Page 28 and 29:
Functional Description Control Elem
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Functional Description Linear Ion T
Page 36 and 37:
Functional Description Orbitrap Ana
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Functional Description Vacuum Syste
Page 44 and 45:
Functional Description Vacuum Syste
Page 46 and 47: Functional Description Vacuum Syste
Page 48 and 49: Functional Description Gas Supply I
Page 50 and 51: Functional Description Cooling Wate
Page 52 and 53: Functional Description Printed Circ
Page 79 and 80: Chapter 2 Basic System Operations M
Page 81 and 82: Basic System Operations Shutting Do
Page 83 and 84: Shutting Down the System Basic Syst
Page 85 and 86: Starting Up the System after a Shut
Page 87 and 88: Basic System Operations Starting Up
Page 89: Basic System Operations Resetting t
Page 92 and 93: User Maintenance General Remarks Ge
Page 94 and 95: User Maintenance Baking Out the Sys
Page 99 and 100: Chapter 4 Replaceable Parts This ch
Page 101 and 102: Parts Orbitrap Analyzer Parts Pumpi
Page 103 and 104: Parts Gas and Water Supply Replacea
Page 105 and 106: Electronic Parts Electronics - Righ
Page 107: Electronics Main Supply Table 4-18.
Page 110 and 111: Glossary: collision-induced dissoci
Page 112 and 113: Glossary: IEEE IEEE Institute of El
Page 114 and 115: Glossary: P/N P/N part number p-p p
Page 116 and 117: Glossary: V dc V dc volts direct cu
Page 118 and 119: Index: D control unit, for turbopum
Page 120 and 121: Index: O O pressure 1-26 pressure r
Page 122: Index: W quality 1-40 safety thresh
show all

LTQ Orbitrap XL Hardware Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?