CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

Jumper Locations1CDK 111321) Rx Termination Jumper Block and Download Connector (J1)2) EDH Insertion Jumper Block (J5)3) GPI, Panel, Tally Jumper Block (J6)Jumper PinoutsEach jumper block (J1, J5, J6) has the same pinout configuration.Pin Numbers, as viewed from component side of card1 23 45 6Jumper ConfigurationsRX Termination Jumper Block and Download Connector(J1)Pins 1, 3, and 5 of J1 configure the terminator resistor on BNC 4. BNC 4 is usednormally as the RS422/RS485 Tx output and must not have a terminator resistorinstalled.Pins 2, 4, and 6 of J1 configure the terminator resistor on BNC 3 when that BNC isused as an RX input connector. BNC 3 is used normally as the RS422/RS485 Rxinput. When several CDK-111A-Lites have this BNC connected in parallel, the lastCDK must have the 120 Ohm terminator installed. All other CDK-111A-Lite cardsin the chain must have the terminator removed. If this Rx input is driven from anRS232 serial port, then the 120 Ohm terminator must be removed on all CDKs.This jumper block can also be used as a connector to serially transfer images andanimation between the card and a PC, using the Serial Download Cable.6-8 • Appendix C. Specifications CDK-111A-Lite • Owner’s Guide v4B
BNC 4 (Tx) RS422/RS485 Jumper Configuration• Bridging pins 3 and 5 removes the 120 Ohm terminator on BNC 4 (Tx) outputfor any position card use.BNC 3 (Rx) RS422/RS485 Jumper Configuration• Bridging pins 2 and 4 installs a 120 Ohm terminator on the Rx (BNC 3) inputfor single card or last card use.• Bridging pins 4 and 6 removes the 120 Ohm terminator on the Rx (BNC 3) inputfor multiple but non-last card use.EDH Insertion Jumper Block (J5)This jumper block is used to insert the EDH information into the PGM and/or PVvideo stream.• Bridging pins 2 and 4 disable EDH insertion on the PGM and PV video outputs.• Bridging pins 4 and 6 enable EDH insertion on the PGM and PV video outputs.This jumper block can also be used to enable or disable STMPE 269M FaultReporting.• Bridging pins 3 and 5 enable STMPE 269M Fault Reporting.• Bridging pins 1 and 3 disable STMPE 269M Fault Reporting.GPI, Panel, Tally Jumper Block (J6)This jumper block is used in conjunction with the menu (software) to define thestatus of BNC 2 – whether it is used as an input for a GPI, an input/output for aControl Panel, or as a Tally output.• Bridging pins 1 and 2 configures the BNC 2 to be used as a GPI input.• Bridging pins 3 and 4 configures the BNC 2 to be used with the DCP111Remote Control Panel unit.• Bridging pins 5 and 6 configures the BNC 2 to be used as a Tally output.Caution — Only one bridge may be installed on the jumperblock J6. Installing more than one bridge may causepermanent damage to the CDK-111A-Lite card. Please notethat contrary to the other jumper blocks, the single bridge onJ6 must be installed horizontally to short circuit either pins 1and 2, or pins 3 and 4, or pins 5 and 6.ImportantThe configuration of this jumper blocks defines the function ofthe BNC 2 connector. The desired operation must also be setupwith the CDK-111A-Lite on-screen menu and must match theconfiguration bridge installed on J6. See Chapter 2,“Installation and Setup” for more details.CDK-111A-Lite • Owner’s Guide v4B Appendix C. Specifications • 6-9
Page 1 and 2:
Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5:
Important Regulatory and Safety Not
Page 6 and 7:
Company AddressRoss Video Limited R
Page 9 and 10:
ContentsIntroduction 1-1A Word of T
Page 11 and 12:
Technical Specifications...........
Page 13 and 14:
IntroductionA Word of ThanksCongrat
Page 15 and 16:
Documentation ConventionsThe follow
Page 17 and 18:
AbbreviationsThe following abbrevia
Page 19 and 20:
Product Comparison ChartFor your re
Page 21 and 22:
A Word about Technical SupportAt Ro
Page 23 and 24:
Installation and SetupIn This Chapt
Page 25 and 26:
OverviewCDK 11111023456798CDK111A-L
Page 27 and 28:
BNC ConnectorsThis section defines
Page 29 and 30:
Single CDK-111A-Lite Settings for R
Page 31 and 32:
Accessing the Menu SystemSetup and
Page 33 and 34:
Control Panel - DCP-111 (Optional)U
Page 35 and 36:
Navigating Through the Menus Using
Page 37 and 38:
The next series allow you to config
Page 39 and 40:
8012345 67Card Address Configuratio
Page 41 and 42:
OperationIn This ChapterThis chapte
Page 43 and 44:
4) Menu Select/FTB Button (SW4)•
Page 45 and 46:
Control Panel - DCP-111 (Optional)T
Page 47 and 48:
GPIs and TalliesThis section descri
Page 49 and 50:
The Menu SystemThe CDK-111A-Lite is
Page 51 and 52:
Menu 1: Runtime ParametersAuto Tran
Page 53 and 54:
Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56:
Menu A: DiagnosticsMenu A: Diagnost
Page 57 and 58:
Menu D: Card SetupTest PatternSelec
Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73 and 74: Bit776655Analog Control Command (45
Page 75 and 76: NotePush-button / Lamp Control Comm
Page 77 and 78: Transition Mode Command (4A, CA)Fun
Page 79 and 80: Rate2=Next most significant digitRa
Page 81 and 82: Software Version Command (6C, EC)Th
Page 83 and 84: Error Status Command (71, 72)The ed
Page 85 and 86: GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88: Command ListThe following table lis
Page 89 and 90: Select Transition Type (0x03, TX_TY
Page 91 and 92: FunctionCrosspoint byte values:00 N
Page 93 and 94: Key Enable (0x0B, KEY_ENABLE)Functi
Page 95 and 96: FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98: either end of the communications li
Page 99 and 100: Appendix B. Software UpgradesIn Thi
Page 101 and 102: CautionCard may be hot to the touch
Page 103 and 104: Appendix C. SpecificationsIn This A
Page 105 and 106: Feature Comparison ChartFeature CDK
Page 107 and 108: CDK-111A-Lite BNC SettingsConnector
Page 109: I/O, Power, Delay SpecificationsTec
Page 113 and 114: Index112-Bit Analog Value..........
Page 115 and 116: GPIabbreviation ...................
Page 117 and 118: SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

Create successful ePaper yourself

Delete template?

Save as template?